It allows any output channel of a compatible dimmer or switch to control a fully loaded circuit of 0-10 VDC fluorescent ballasts1, non-dimmed lighting (incandescent, HID, magnetic low voltage (MLV), electronic low voltage (ELV), neon/cold cathode, and fluorescent ballast) up to 16 amps, and motors rated up to 1/2 HP @ 120 Volts, 1 HP @ 230/277 Volts. The CLS-EXP-DIMFLV is designed for mounting to a vertical surface. Conduit knockouts are provided on the bottom and lower sides. All connections a

©2008 Crestron Electronics, Inc. Contents Swivel Mount Kit for TPS-6X: SMK-6X 1 Introduction...............................................................................................................................1 Features and Functions................................................................................................1 Specifications..............................................................................................................1 Physical Description.............

The Exit and Run Program button verifies that all of the setup information has been saved to the EEPROM and displays the main page that has been programmed into your system. The remaining buttons on the MAIN MENU open other menus which are discussed in subsequent paragraphs. MAIN MENU Calibration Menu CALIBRATION MENU Touch Perform Calibration. The message “Touch Upper Left” appears centered on the panel with a cross hair in the upper left corner. Touch the center of the cross hair in the corner

3.63 in(9.22 cm) 2.25 in(5.72 cm) 6.25 in(15.88 cm) FROM (included) AC POWER PACK WARNING: To avoid possible physical harm, damage to the TPMC-4XG-DS or touchpanel, use only the included power pack (100-240 VAC, 50/60 Hz) when charging. WARNING: Charge the touchpanel in a well ventilated area away from sparks and open flame. Do not use the touchpanel near heat sources such as radiators, heat registers, stoves or other apparatus. CAUTION: Avoid accidental shorting of the electrical contacts to pr

©2007 Crestron Electronics, Inc. Contents Isys® G-Series Touchpanel Interface: TPS-GA-TPI 1 Introduction...............................................................................................................................1 Features and Functions................................................................................................1 Internal Block Diagram...............................................................................................3 Specifications..............

All brand names, product names and trademarks are the property of their respective owners. ©2010 Crestron Electronics, Inc. Contents Battery Pack for TPS-6X: TPS-6X-BTP 1 Introduction...............................................................................................................................1 Features and Functions................................................................................................1 Specifications......................................................

...............................................................................15 How the Program Works...........................................................................................15 How to Create the Program .......................................................................................16 Reserved Join Numbers.............................................................................................19 Problem Solving ......................................................

When the touchpanel is unlatched, it snaps outward slightly, and then may be removed by hand. The control system program defines the method (i.e., touchpanel button) of unlatching. Electrical Undocking of Touchpanel 1. Via the touchpanel and/or control system program, unlatch the touchpanel. 2. Pull the upper edge of the touchpanel outward and remove the touchpanel. Remove STX-1700CW Manual Undocking of Touchpanel The STX-1700CW can be undocked manually. The only tool required is a long-reach (m

Within a single jacket, DM-CBL-NP contains one high-bandwidth/low-crosstalk shielded 4-twisted pair (STP) cable, one CAT5e unshielded 4-twisted pair (UTP) cable, and one DMNet cable. The STP “Video Data” cable, which connects to the ‘D’ port of a DigitalMedia device, is of a specialized construction designed to allow the longest possible cable lengths* for transporting high-definition digital video and audio. The Cat5e “Data Management” cable, which connects to the ‘M’ port, carries high-speed E

The “TMK-6X-DSW Procedure” starts below and the “WMKT-6X-DSW Procedure” starts on page 6. Be sure to review each procedure before starting. TMK-6X-DSW Procedure This section provides the necessary steps for the assembly of the TMK-6X-DSW with either the BB-6X-DSW or PMK-6X-DSW. It is assumed that the BB-6X-DSW or PMK-6X-DSW has been secured to the stud according to the instructions in the latest revisions of their Installation Guides (Doc. 6728 and Doc. 6778 respectively). It is also assumed tha