Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
When the touchpanel is unlatched, it snaps outward slightly, and then may be removed by hand. The control system program defines the method (i.e., touchpanel button) of unlatching. Electrical Undocking of Touchpanel 1. Via the touchpanel and/or control system program, unlatch the touchpanel. 2. Pull the upper edge of the touchpanel outward and remove the touchpanel. Remove STX-1700CW Manual Undocking of Touchpanel The STX-1700CW can be undocked manually. The only tool required is a long-reach (minimum 4-1/2 inches from tip to handle base) #1 flat or Phillips screwdriver. 1. Refer to the diagram below. At top-center of the front panel, remove the manual unlatch access plug from the access hole. Remove Access Hole Plug 2. As shown in the following diagram, insert a long-reach screwdriver into the access hole at a downward angle (approximately 10o) until the tip of the screwdriver contacts the manual unlatch tab. Insert Screwdriver 3. As shown below, lower the handle of the screwdriver until the touchpanel unlatches (handle of screwdriver will be approximately level and touchpanel will snap outward slightly). Lower Screwdriver Handle 4. Refer to the diagram below. By hand, undock the touchpanel by pulling the upper edge of the touchpanel outward and remove the touchpanel. Remove STX-1700CW 5. Refer to the diagram below. Re-install the access hole plug into the access hole. Re-Install Access Hole Plug Identity Codes The STX-1700CW touchpanel uses three distinct types of identity (ID) codes: Cresnet identity (Net ID), RF ID, and RF CHANNEL. These codes are assigned to the touchpanel from the Cresnet Interface menu when the unit is configured. Refer to “Setup Menu” on page 12. For the touchpanel to be identified within the Cresnet system, these assignments must match assignments made in the SIMPL Windows project. Net ID Every equipment and user interface within the Cresnet system requires a unique Net ID. These codes are recognized by a two-digit hexadecimal number from 03 to FE. The Net ID of the unit must match the Net ID specified in the SIMPL Windows program when operating as a wired touchpanel (optional, recommended for testing). The Net ID is used when the touchpanel is wired directly to the control system during uploading a Crestron VisionTools® Pro-e (VT Pro-e) project or upgrading the touchpanel firmware. RF ID Every STX-1700CW touchpanel communicating with a Cresnet control system via a STRFGWX requires a unique RF ID to secure RF communications. There are 15 useable codes for multiple touchpanel(s) ranging from 1 to F (hexadecimal number). The RF ID of the unit must match the RF ID specified in the SIMPL Windows program. For roaming details, refer to “Modifying a SIMPL Windows Project for Roaming” on page 21. RF CHANNEL Each STX-1700CW touchpanel communicating to the STRFGWX transceiver must have an RF CHANNEL that matches the RF CHANNEL of the STRFGWX. There are 16 possible RF CHANNELS ranging from 0 to F (hexadecimal number). NOTE: A single RF CHANNEL may be used by more than one STRFGWX when multiple transceivers are used to expand the roaming capabilities of a touchpanel. For more information, refer to the latest revision of STRFGWX Operations Guide (Doc. 5811) available from the Crestron website (Configuring the Touchpanel MAIN MENU This menu can also be obtained via digital reserved join number, 17242. To configure the unit, it may be necessary to access a series of setup screens prior to viewing run-time screens that are loaded into the touchpanel for normal operation. The MAIN MENU for configuring the touchpanel appears when a finger is held for about five seconds from the power off state. Upon entering SETUP MODE, the MAIN MENU, shown to the left, displays four buttons: Touch Screen Calibration, Exit and Run Program, Setup, and Diagnostics. Selecting Exit and Run Program verifies that all of the setup information has been saved to EEPROM and displays the main page that has been programmed into the touchpanel. The remaining buttons on the MAIN MENU open other menus, which are discussed in subsequent paragraphs. Calibration Menu CALIBRATION MENU Calibration of the touchscreen is required if the active touch area of a button does not coincide with the button's image. Select the Touch Screen Calibration button to display the CALIBRATION MENU, as shown to the left. The CALIBRATION MENU offers the choice to initiate calibration with the Perform Calibration button or return to the previous screen with the Return button. Choose an option by touching the appropriate button. If you need to calibrate the touchpanel, the screen displays the message "Touch Upper Left" centered on the panel with a cross hair in the upper left corner. Touch the cross hair to initiate calibration. Another message, "Touch Upper Right", appears with a cross hair in the correct corner. Touch the cross hair. A final message, “Touch Lower Right”, appears with a cross hair in the correct corner. To...