The JET JWP-15DX and JWP-15HH have two material feed rates –20 FPM (Feet Per Minute) used primarily for rough dimensioning and 16 FPM to increase the cuts-per-inch to create a silky-smooth surface. A push/pull knob shifts between the feed rates on the fly. The rollers are driven by a gear and chain drive with an automatic chain tensioner, housed in a cast iron case. The gear section runs in an industrial style oil bath for maximum control over long-term wear. The all-metal adjustable feed roller

9.................Washer.................................................................................................6 3 0........FS1636N-30.................Spring Cap...........................................................................................4 3 1........FS1636N-31.................Gib.......................................................................................................2 3 2........FS1636N-32.................Screw............................................

1 29........ JWL1642-129 ...............Plate...................................................... ............................................... 1 ........JWL1642-130...............Digital Readout......................................JWL-1642EVS........................1 ............JWL1642-130A.............Digital Readout......................................JWL-1642EVS-2.....................1 31........ TS-1540011..................Nut ........................................................

Sheet metal outfeed table with b. height adjustment Planing and joining tables lock c. Precision ground table top d. Oversized, ergonomic knobs e. Integrated cord wrap f. C FB SpecificationS Stock number 707400 Model number JJP-8BT Motor 120V, 60Hz, 13Amp Knife Size (in.) 8.25 x .65 x .06 number of Knives (RpM) 2 cutting Speed 9,000 cuts per Minute cpM 18,000 feed Speed fpM 19.5 Max. cutting Width (in.) 8 Jointer Max. cut Depth (in.) 1/8 planer Max. cut Depth (in.) .08 cutting thickness (in.) .2

If in doubt, use the next heavier gauge. Remember, the smaller the gauge number, the heavier the cord. Volts Total Length of Cord in Feet 120V 25 50 100 150 AWG 12-16 Amps 14 12 Not Recommended 5 230 Volt Operation If 230V, single-phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This lathe is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 2

Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This dust collector is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a dust collector, do not use

BD920N-CS09......... .........Rivet............................................... ..................2x5................ ...........2 10 ... 5020......................... .........Graduated Ring.............................. ...........1 11... ... BD920N-CS11......... .........Key................................................. ..................3x13.............. ............1 12... ...5023......................... .........Spring............................................. ............1

BOX 1349 Auburn, WA 98071-1349 Ph: 1-800-274-6848 ■ Fax: 1-800-274-6840 E-mail: jet@wmhtoolgroup.com M-708640 2/03 Copyright © WMH Tool Group This manual has been prepared for the owner and operators of JET’S DC-650A. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from

3. Secure bag to housing with retaining strap. Note: The retainer strap should be tight enough to provide a good seal. Collector Bag Installation – DC-650A/ARC 1. Insert the snap ring of collector bag into the bottom of housing at an angle, see Figure 6. 2. Pull down on the ring and bag to make sure it “seats” in the housing. After completing the filter bag and collector bag installation, proceed to Electrical Connections. 9 Figure 5 Figure 6 Canister Installation – DC-650C/CRC 1. Place the cani

This new 10HP ZX Series lathe boasts a 22" swing over bed and comes standard with a 10" 3-jaw chuck with top reversing jaws and a 12" 4-jaw chuck. The 22" ZX Series Large Spindle Bore Lathe comes equipped with a 3-1/8" bore spindle supported by two tapered bearings and one ball bearing and a universal gear box with pitch threads in inches, metric, diametral and module. The universal gear box is dial controlled eliminating the need for changing end gears. The GH-2280ZX also comes standard with a