4) Gather all cables to one side and tie off to unused holes on underside of Docking Station. Insert as many zip ties as necessary to secure cables. 7 • 1-800-524-9900 Cable Management (continued) 5) Create a service loop with cables to ensure that no tension is on the connectors and to enable intended motion. 6) Tie off cables onto a stationary part of the mounting system. This loop must be large enough to allow full range of expected rotation and extension without stressing connections. Collec

DOOR WINDOW GUARDS: 1. In order for guard to fit properly on frame, you must permanently remove the upper plastic trim on doors. The top of the lower door panel may have to be trimmed approximately .” to .”. (Note: Place guard on window frame to determine possible trimming). See section 8 – door window guard does not have cutouts for window latches (making them inoperable). 2. With the doors open, hold the window screen up to the window/door frame. The guard framework should fit evenly around th

• THE ANTENNA MODULE IS NOT A HANDLE. DO NOT USE IT TO CONNECT OR ENGAGE THE COMPUTER TO DOCKING STATION. DO NOT USE IT TO CARRY THE DOCKING STATION. • THE DS-PAN-410 SERIES DOCKING STATIONS ARE DESIGNED EXCLUSIVELY FOR USE WITH PANASONIC CF-53 TOUGHBOOK COMPUTERS ONLY AND ARE NOT BACKWARD COMPATIBLE WITH THE PANASONIC CF-52 COMPUTER • FOR DOCKING STATION MODELS EQUIPPED WITH AN INTEGRATED POWER SUPPLY (DS-PAN-412, DS-PAN-412-2, PKG-DS-PAN-412, PKG-DS-PAN-412-2), REFER TO THE SUPPLIED LIND POWER

Bend window guard so it contours the door as shown in photo #1. Determine the proper window guard for each window. If installing aluminum door panels refer to those instructions at this time. They will need to be installed first. 2. 3. WGI-D22-INST-10-06 INSTALL WINDOW GUARDS • Loosely attach upper mounting bracket to window guard using H” x /” tamper proof screws and flat washers. • Position screen to vehicle as shown in photo #2. • Make sure you have the window guard centered on the d

KR-SB-800-SL with Magnafire KR-3X or KR-51 Lighthead: Closed height: 50.5" (Tripod is 41.75" closed without the light) Part Number Description KR-SB-831-SL 800 Series Short Tripod with KR-31 Magnafire 3000® Lighthead (70W, 12V, 6 amps) KR-SB-832-SL 800 Series Short Tripod with KR-32 Magnafire 3000® Lighthead (150W, 12V, 13 amps) KR-SB-851-SL 800 Series Short Tripod with KR-51 Space Saver Magnafire 5000® Lighthead (70W, 12V, 6 amps) KR-731 700 Series Portable with KR-31 Magnafire 3000® Light

Torque screws to 80 in-lbs (9.0 Nm) ± 10%. 1/4”-20 Screws 6 Cable Management 1) Tip the Docking Station to a position that is comfortable to work with. 2) Install all cables that are necessary for computing needs. 3) Use Zip Ties (Hardware Kit Item 1) to strain relieve cables at rear of Docking Station. IF SECURING EXTERNAL ANTENNAS TO DOCKING STATION (DS-PAN-411-2, DS-PAN-412-2, PKG-DS-PAN-412-2) LEAVE AN ADEQUATE SERVICE LOOP BETWEEN THE ANTENNA CONNECTOR AND THE FIRST ZIP TIE ON THE DOCKING S

Determine location to obtain both. • With offset bracket positioned against flat surface, (i.e., console, divider wall, etc.), mark and drill 5/16” hole at location of bolt on offset bracket. • Bolt offset bracket to “flat surface” using a fender washer and 5/16” nut. • Bolt C-PED1612 to floor of vehicle using /” x 1” -1 /” hex head lag bolts, depending on particular vehicle application. • Mount optional laptop mounts (C-3090 series), monitor mounts (C-3522), keyboard mounts (C-3329) or tilt

They will need to be installed first. 'üïïiïïKîï; ^ ‘ïï!ïîïrÂ4 и»4 * WGI-D23-INST-10-06 INSTALL WINDOW GUARDS • Loosely attach upper mounting bracket to window guard using H” x /” tamper proof screws and flat washers. (This step may already be done during shipping) • Position screen to vehicle as shown in photo #2. • Make sure you have the window guard centered on the door. • Mark, drill 1/8” holes, and attach lower mount using #10 x /” screws as shown in photo #3. Note: Be sure the u

• Using a 9MM socket, remove the spring clip and nut. • Immediately reinstall the nuts only. • Put two #10 washers onto the same bolt on top of the nut. • Put spring clips on top of the washers. NOTE: More washers can be used if needed. Make sure to leave sufficient threads for metric nut. • Using a 7MM socket, put the M4 x 7MM nut (supplied in this kit) on the stud to the hold spring clip and washers. Proceed to the next spring clip. • When all the spring clips are reinstalled, the interior tri

For questions regarding the set-up of your DS-DELL-100 Series/220 Series Docking Station, please contact Havis at 1-800-524-9900 or visit for additional product support and information. This Owner’s Manual applies to the following Part Numbers: DS-DELL-101 DS-DELL-101-3 DS-DELL-103 DS-DELL-221 DS-DELL-223 • NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE. • DO NOT USE COMPUTER WHILE DRIVING. • READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION. •