The symptoms of poor performance related to wet wood include: •Difficulty getting a fire going and keeping it burning well • Smokey fires with little flame • Dirty glass • Rapid creosote build-up in the chimney • Low heat output • Short burn times, excessive fuel consumption and blue/grey smoke from the chimney. To help avoid large build-ups of tar and creosote within the stove and the flue system, it is recommended to burn at high output for at least 30 minutes each day. The use of Stovax Prote

Contact Stovax to obtain further information. IMPORTANT Please read these instructions carefully before using the appliance. Keep them safe for future reference and when servicing the appliance. PM123-Issue 1 (July 2004) FOR YOUR RECORDS To assist us in any Guarantee claim please complete the following information:- Stovax dealer appliance was purchased from Name: .....................................................................................................................................

See Diagram 14. 14 AR1115 6.5 Flat fronts (All others) - Place 3 large coals and 4 small coals onto the front coal moulding ensuring that they rest against the decorative front, these should run intermittently small, large, small etc. See Diagram 15. 15 AR1116 6.6 Place 5 large coals onto the flame baffle fingers. See Diagram 16. 16 AR1117 6.7 Place 4 large coals so that they form a bridge between the other 2 rows, and 2 small coals, 1 at each end. Place 4 large coals at the back of the fire. Se

518 Place six small coals along the rear of the flame baffle, resting against the rear ledge, see diagram 21. NOTE: ENSURE THAT THE COALS ARE POSITIONED, AS DETAILED ABOVE. ONLY USE THE CORRECT AMOUNT OF COALS, AS SPECIFIED IN DIAGRAMS. 5.19 Ensure that the fibreglass seal on the back of the door is intact, locate the door on the four studs and slide back to the firebox. Secure in place using the four brass nuts and the tool supplied, do not over tighten the nuts, see diagram 22. Keep the tool w

1.4 THERMOSTATIC AND TIMER REMOTE CONTROL. This remote controls the gas appliance after the pilot has been lit. In ‘MANUAL MODE’ it can be used to turn the main burner on and manually regulate it from low through to high and back again. It can also be used to turn the main burner leaving the pilot burning. In ‘AUTO MODE’ it will automatically regulate the room temperature to a pre-set temperature. In ‘TIMER MODE’ it will turn the fire on and off according to a pre-set programme and automatically

10.1 Turn the gas supply off at the isolation device. 10.2 Locate the aeration plate on the underside of the airbox and remove the Nyloc nut, see diagram 15. 10.3 Remove the plate and replace with the correct size, ensure that the hole(s) in the plate align correctly with the holes in the underside of the airbox and replace the Nyloc nut. 11.1 In order to change between gas types, it will be necessary to change the following items. • Pilot Unit • Control Valve • Main Injector • Aeration Plate (i

5.1 Remove the door by undoing the four dome nuts using the tool supplied and place to one side. 5.2 Carefully remove the ceramic fuel bed components and place to one side taking care to protect floor coverings etc, PLEASE HANDLE WITH CARE. 5.3 The coals should not require cleaning. Do not use a vacuum cleaner or brush to clean the coals, any large pieces of debris can be removed by hand. 5.4 Ensure any debris is removed from the burner ports. 5.5 Replace the ceramics by referring to section 6.

coal, soot etc. which could short the spark, clean the area. Problem is with the pipework or fittings which lead to the fire. Correct and retry. Is thermocouple connection good in back of valve? Replace oxypilot. Will pilot stay alight? Change mag unit. Is the pilot flame of the correct length? See diagram 1, Servicing Requirements Change the pilot unit. Will pilot With the pilot stay lit? running is the gas pressure stated on the databadge? With the fire running on full is the gas at the pressu

4.3 Replace with a new ignition lead following the same route as the old one. Replace the valve cover and the pilot assembly. 4.4 Check operation of the new ignition lead. 5.1 The piezo assembly used on this appliance is not serviceable and is unlikely to fail. 5.2 If a new piezo is required it will be necessary to change the gas valve. Refer to Section 6. SERVICING INSTRUCTIONS REPLACING PARTS 4. IGNITION LEAD AND PIEZO 5. PIEZO 3. PILOT UNIT 5 6 7 8 AR0915 AR0916 22 6.1 Turn the gas supply off

7.9 Ensure that the fibreglass seal on the back of the door is intact, locate the door on the four studs and slide back to the firebox. Secure in place using the four dome nuts and tool supplied. Do not overtigthen the nuts, see diagram 10. NEVER OPERATE THE STOVE WHEN THE DOOR IS REMOVED. USER INSTRUCTIONS 5 AR1613 6 AR1614 7 AR1615 8 AR1616 9 AR1617 10 AR0540 8. THE FLAME FAILURE DEVICE 8.1 This is a safety feature incorporated in all GAZCO fires which automatically switches off the gas supply