Neben einer besseren Klangwiedergabe hilft eine korrekte Verstarkungseinstellung auch, die Zuverlassigkeit Ihres Verstarkers zu steigern, da exzessive Innentemperaturen vermieden werden, die durch inkompatible Radioausgange bzw. Verstarkereingange erzeugt werden. Hinweis: Ein Hochdrehen der Eingangsverstarkung bringt nicht mehr Leistung. Nur mehr Storgerausche. Der Eingangsverstarkungsregler ist kein Leistungsregler. Wenn der Fernbedienungsregler verwendet wird, verbinden Sie dessen Stecker mit

Ground: 10 AWG. Remove Paint -From Metal ForjnslajlatjonoptionsgoJomtxçvm.

Ground: 10 AWG. Remove Paint -From Metal ForjnslajlatjonoptionsgoJomtxçvm.

100dB A-Weighted • Frequency Response: >100 • Frequency Response: 20Hz-200Hz ± 3dB • Maximum Input: 8Vrms • Thunder EQ: Variable Bass Boost (0-18dB) centered at 40Hz • Crossover: Variable 40Hz to 200Hz, 24dB/Octave Low Pass • Dimensions: 11.5" x 9.75" x 2.1" (29.3cm x 24.8cm x 5.3cm) 2627 POWERAMPLIFIEROWNER’SMANUALPOWERAMPLIFIEROWNER’SMANUAL Installation Jegliche Abweichung von den empfohlenen amVerstarker, an den Lautsprechern und/oder am Sie die Verbindung vor dem Einschalten des Systems. 1.

3. Wenn der volle Bereich (FR) gewahlt wird, dient der Verstarker als Fullrange-Verstarker. Auswahl der Crossover-Frequenz (FREQ) Sowohl der Hochpass- als auch der Tiefpassbereich bieten kontinuierlich anpassbare Crossover-Frequenzen zwischen 40Hz und 350Hz. Stellen Sie den Wert je nach den Leistungswerten Ihrer Lautsprecherkomponenten oder Ihrem eigenen Geschmack ein. Bass-Boost-Regler (BASS BOOST) Wahlen Sie ein Boost-Niveau zwischen 0dB und +18dB bei 40Hz, um die Bassleistung Ihres Sound-Syst

Do not connect to Factory bolts of ANY kind. When attaching the ground to the chassis, sand all the paint away from the contact point, a grounding block like the StreetWires GT4 should be used whenever possible, this piece of equipment has 5 times the surface area a normal screw has. The gauge of the power and ground wire is often an overlooked aspect of amplifier installation. The more power the amplifier receives, the more power it will produce. Power cables have a natural resistance, and will

Securely mount the amplifier. If everything is in order, reconnect the vehicles negative battery connection and begin following the feature setup and adjustment steps. Feature Setup and Adjustments 1. Selecting The Input Sensitivity Range – Before you turn on your system, you must select the proper input sensitivity range on your amp using the button labeled INPUT SENS located in the GAIN CONTROL section of the control panel. • Setting for aftermarket Source Units: Refer to your aftermarket owne

Normal source units can only keep a constant 12 volts to 2 or possibly 3 amps. This wire should also be run on the away from RCA cables. • CAP+: This 8 gauge terminal is internally wired in parallel with the +12V on the StreetWires Power connector. It is the ideal connection point for the positive side of a capacitor to increase the amplifier’s performance. • CAP-: This 8 gauge terminal is internally wired in parallel with the GND on the StreetWires Power connector. It is the ideal connection po

Adding MTX amplifiers and matching MTX speakers and subwoofers with StreetWires connections will put you in a better position to hear, feel, and experience all of the music the artist intended. Specifications Primary Ratings: Power Output: 250 watts RMS x 1-channel at 4 ohm and . 1% THD+N Signal-to-Noise Ratio (1 watt): 71dB Secondary Ratings Power Output: 500 watts RMS x 1-channel at 2 ohm and . 1% THD+N THD+Noise (Distortion) (1 watt): . .5% Frequency Response (-3dB): 20Hz-200Hz Maximum Input

If the specification is not available, please follow the instructions listed below. X1 POSITION: 100mV–1V (Typically for RCA Input) • Setting for Factory (OEM) Source Units: To check the amount of voltage that is present from the source unit, take a multi meter, or a volt/ohm meter, on the A/C setting, (range from 100mV up to 10 volts) attach the positive and negative leads directly to any exposed speaker. It will not matter if the polarity is correct, it will read the same amount of voltage. X