Loosen and remove the blade cover locking knobs (10). 3. Remove the blade cover (9). 4. Take the 2 face spanners and use 1 to hold the blade securing nut and the other to hold the flat part of the spindle. Turn the spanner holding the blade securing nut in an anti-clockwise direction to loosen the nut. 5. Remove the nut, outer blade flange and blade. 6. Wipe a drop of oil onto the inner blade flange and the outer blade flange where they contact the blade. 7. Fit the new blade onto the spindle ta

Quick reference guide Operation Speed • Cutting metal 5 - 6 • Sanding wood 5 - 6 • Cutting hard metal 5 - 6 • Engraving metal 4 - 5 • De-burring 4 - 5 • Drilling holes 4 - 5 • Removing rust 3 - 4 • Sharpening 3 - 4 • Polishing 1 - 2 Holding the tool 1. For jobs such as milling or engraving where precision is required, hold the tool like a pen. 2. For heavier work like cutting or grinding hold the machine in the palm of your hand. Changing accessories 1. Make sure that the machine is switched off

Do not leave a battery charging for longer than 24 hours. 1. Align and slide the slim line adaptor (9) onto the battery until the battery pack latches “click” into position. Check the adaptor is flush with the battery and there is a firm connection. 2. Connect the power supply from the charger to the slim line adaptor via the socket in the rear of the adaptor housing. 3. Plug in the charger and switch on. The red LED indicator will show power to the adaptor and that charging is taking place. 4.

To fit the shoulder strap (11), simply open the buckle on the strap and fit it through the hole provided on the housing of the blower/vac. Operation of the blower vac Prior to using the blower vac, ensure you have read and understood this instruction manual. Ensure you are wearing suitable clothing and also safety equipment like safety glasses, ear protection and a mask if necessary. Ensure the attachments to the blower vac are correctly fitted and adjusted. Be aware of other people and animals

If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Switching on and off 1. Connect the plug to the power supply. 2. Push the left-hand side “I” of the sealed on/off switch (1) to start the motor. 3. Push the right-hand side “O” of the sealed on/off switch (1) to stop the motor. 4. Hold the tool securely and make sure that you have full control at all times. Using the san

There are 3 levels of charge low, medium and high. When the battery indicator is showing only 1 LED (low) the battery should be removed and put on the charger. LED Work area light The drill has 3 LED lights (11) to illuminate the work area and improve vision when drilling in areas with insufficient light. To turn the LED lights on and off depress the LED light switch (13). Using the drill Use the forward/reverse switch (4) to select the direction of rotation, then pull the trigger (3). This trig

• Always transport and store fuels in an approved container. • Never place flammable material close to the engine muffler. • Do not use petrol which contains ethanol or methanol as it may damage the fuel lines and other engine parts. J K H I • Mix only enough fuel for your immediate needs. Do not store the mixed fuel mixture. Starting the brush cutter Choke control Start position (choke closed). Run position (choke open). 1. Move the ignition switch (11) to the on position marked with a (Fig. L)

Note. Grip the rubber straps at the fixed end and stretch evenly over the tank until the straps are connected securely to the support brackets. WARNING. When extending the rubber straps be careful. If released early they can flick back and hurt you. Make sure that your face is at a safe distance from the rubber straps while they are being stretched. CAUTION. Over stretching the rubber straps may result in fracturing the straps. 6. Reconnect the tank 1 inlet hose (25) onto the combination valve (