Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Global Machinery Company Dateigröße: 322.19 kb Dateiname: 96bf9304-12c7-28f4-c9e4-3f257af8c604.pdf Unterrichtssprache:

Do not leave a battery charging for longer than 24 hours. 1. Align and slide the slim line adaptor (9) onto the battery until the battery pack latches “click” into position. Check the adaptor is flush with the battery and there is a firm connection. 2. Connect the power supply from the charger to the slim line adaptor via the socket in the rear of the adaptor housing. 3. Plug in the charger and switch on. The red LED indicator will show power to the adaptor and that charging is taking place. 4. The battery charging time is approximately 3–5 hours. The red LED goes out when the charging cycle is complete. Turn off the charger power supply from the mains and then remove the battery from the line adaptor. To obtain the best life for the battery Never allow the drill to come to a complete stand still before recharging. The battery should be placed on charge whenever the battery is noticeably running down or the drill no longer performs a task it previously performed. Avoid conducting short charges. Make sure that the battery is fully charged every time by allowing the charger to complete its full charging cycle. Avoid allowing lose items like screws or nails etc to be stored with battery packs as these or similar items can short battery packs and cause a fire or explosion. Always unplug the charger when not in use and store in a dry secure place. Avoid charging or storing your battery in temperatures below 0.C and above 40.C. Battery indicator To activate the battery indicator feature first pull the trigger switch (3) then press the battery indicator button (12), this will display the level of charge remaining in the battery. There are 3 levels of charge low, medium and high. When the battery indicator is showing only 1 LED (low) the battery should be removed and put on the charger. LED Work area light The drill has 3 LED lights (11) to illuminate the work area and improve vision when drilling in areas with insufficient light. To turn the LED lights on and off depress the LED light switch (13). Using the drill Use the forward/reverse switch (4) to select the direction of rotation, then pull the trigger (3). This trigger switch is an electronic variable speed control which enables the user to vary the speed continuously. The speed varies according to how far the trigger switch is depressed, the further it is depressed the faster the chuck will rotate and the lighter it is depressed, the slower it will rotate. To stop the drill, release the trigger switch. Note. You can only change the direction of rotation of the drill using the forward/reverse switch when the trigger is NOT depressed. Forward/reverse switch This switch (4) will allow you to change the direction of the motor while the trigger switch is not depressed. Drilling uses the forward mode. The reverse mode is intended for the removal of screws. Adjustable torque This drill is equipped with 20 torque settings plus one drill setting which are controlled by the torque collar (2). By rotating the collar behind the chuck, it is possible to adjust the torque. This will allow better control when using the drill as a screwdriver as it prevents over-tightening of the screws. For drilling, always use the use the Drill position by aligning the Drill symbol with the triangular indicator on the front face of the drill near the torque collar. For setting the torque position, select a low setting on the torque collar and align the selected symbol with the triangular indicator on the top of the drill. Increase gradually to set the correct torque. It is better to use a scrap piece of material if possible to set the torque. Inserting and removing bits This drill has a keyless chuck, which means that a chuck key is not needed to secure a bit in the drill. 1. Open the chuck by holding the rear section of the chuck firm and rotating the front section in a anti-clockwise direction, sufficiently enough to allow the drill bit required to fully enter the jaws of the chuck. 2. Ensure the drill bit is fully inserted, so that the chuck jaws grip the straight section of the bit. 3. Holding the rear section of the chuck firmly, rotate the front section of the chuck clock-wise until the jaws tighten on the drill bit. The front section of the chuck needs to be tightened firmly to ensure the drill bit is held securely. 4. To remove the drill bit, hold the rear section of the chuck firmly and rotate sharply the front section of the chuck in a anti-clockwise direction, sufficiently enough to allow the drill bit to be removed. Adjustable side handle 1. Turn the side handle clamp knob (6) anti-clockwise to loosen the collar fully and slip it over the chuck (1) onto the drill. 2. Adjust the position of the side handle (5) to suit the application and tighten the side handle clamp knob (6) to secure it in place. Drilling Drilling metals • Always clamp sheet metal. • Support thin metal with a block of wood to avoid distorting it. • Use a punch to mark the centre of the hole. • Use a suitable l...

Herunterladen

Geben Sie zwei Ziffern: