Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Note. Grip the rubber straps at the fixed end and stretch evenly over the tank until the straps are connected securely to the support brackets. WARNING. When extending the rubber straps be careful. If released early they can flick back and hurt you. Make sure that your face is at a safe distance from the rubber straps while they are being stretched. CAUTION. Over stretching the rubber straps may result in fracturing the straps. 6. Reconnect the tank 1 inlet hose (25) onto the combination valve (8), by depressing and sliding back the sleeve of the quick coupler valve while reconnecting the hose. 7. Open the tank 1 isolation valve (18). Note. When the isolation valve is opened and there is is compressed air in the lower tank you will hear the air equalise into the top tank. The portable air tank has been properly installed and connected to the air compressor unit. Your air compressor is now ready for use. WARNINGS. 1. Never attempt to remove any electrical component whilst the compressor is connected to the power supply. Switch off the power and remove the electrical plug. 2. Do not adjust the safety valve. 3. Do not use an electrical extension cable. 4. Ensure that the lubricating oil is clean and that the oil level is maintained at the mid point of the red circle in the oil sight glass (16). 5. Take care when discharging air from the tank, i.e. from the safety valves (7), the drain cocks (9) or the air outlets (4 and 27). Compressed air can be extremely dangerous. Take care the discharge air does not cause dust, stones or any other foreign particles to be blown through the air and that the air is discharged in a safe manner. Troubleshooting Trouble Possible cause Possible remedy Motor will not run, running too slow or becoming excessively hot Power fault or supply voltage too low Check the power supply Power cord too long or too thin Use authorised service centre to replace the power cord Faulty pressure switch Use authorised service centre to repair or replace the switch Faulty motor Use authorised service centre to repair or replace the motor Main compressor sticking/tight Use authorised service centre to repair or replace faulty parts Main compressor sticking/tight Moving parts damaged by heat due to insufficient lubrication Use authorised service centre to check crankshaft, bearings, con rod, piston rings, etc and replace where necessary Moving parts damaged or blocked by foreign particle Vibration or abnormal noise Loose part Use authorised service centre to check and repair if necessary Foreign body in main compressor Use authorised service centre to check and clean if necessary Piston connecting with the valve seat Use authorised service centre to increase size of gasket Moving parts excessively worn Use authorised service centre to repair or replace Troubleshooting continued Trouble Possible cause Suggested Remedy Insufficient pressure or decreased outlet capacity Motor running too slow Use authorised service centre to check and repair if necessary Dirty air filter cartridge Clean or replace the filter cartridge Leaking safety valve Use authorised service centre to repair or replace the switch Leaking pipe Use authorised service centre to check and repair if necessary Damaged gasket Use authorised service centre to check and repair if necessary Damaged or carbon coated valve seat Use authorised service centre to check and repair if necessary Damaged piston ring or cylinder Use authorised service centre to check and repair if necessary Open drain cock Check both drain cock(s) are closed, if not immediately switch off the unit as per the shut down instructions and close the drain cock(s) Safety valve fully leaking Check out the condition of the safety valve. If the valve is leaking immediately shut off the compressor and cease using. Have the unit serviced/checked by an authorised service centre and repaired. Don’t continue to use the unit with a leaking safety valve. Air line hose leaking Examine the air hose for any holes and tears. If you find any holes or tears replace the air hose Air fittings leaking Check all air fittings. Make sure that they are tight and not leaking at the joins. If a quick release fitting is leaking, disconnect it and reconnect it. If it continues to leak replace the defective fitting(s). If a male or female fitting is leaking around the thread tighten using a spanner. If the fitting is already tight and can’t be tightened, unscrew the connection and remove the Teflon tape. Examine the condition of the fitting(s). If the a fitting(s) is damaged replace and reassemble using Teflon tape on threaded fittings. If the fittings are OK reapply Teflon tape and reassemble. Troubleshooting continued Trouble Possible cause Suggested Remedy Excessive oil consumption Oil level too high Maintain the oil at the correct level Hole in oil filling plug (14) blocked Check and clean Piston ring and/or cylinder worn or damaged Use authorised service centre to check and repair if necessary Mainte...