drains electrical conn. 6" min 17" (432 mm) 18.875" (479mm) 18.875" (479mm) ice transport tube 12" min counter top 32.375" (823mm) Side View 24.62" (626mm) 30" (762mm) 15" (381mm) 10" (254mm) 2" (51mm) ice waterbath (VU300B only) 8.5" (216mm) ice transport tube entry 27.5" (699mm) bin signal power 3/4" drain nipple 1/2" ID drain tube beverage lines 6 Dual-sided dispensers Required clearances 60" (1524mm) above counter for installation if dispenser will be dropped into counter 49" (1245mm) above

1. Power switch in OFF position or faulty. 2. Bin signal switches in OFF position or faulty. 3. Faulty bin thermostat. 4. Faulty transformer. 5. Icemaker related problem. 6. Faulty run capacitor. 1. Check switch and replace if necessary. 2. Check switch and replace if necessary. 3. Replace bin thermostat. 4. Replace transformer. 5. Refer to icemaker Operation and Service Manual for diagnosing. 6. Check for power and bin signal on icemaker PC board. If problems persist after following this basic

Up to 150 lbs (68kg) of ice storage. Standard equipment includes 6" to 9" (153 to 229mm) adjustable legs for undercounter dispenser support. Dispensers are auto-fill ready to accept (2) Follett Satellite-fill™ Chewblet® icemakers, for drop-in or slide-in installations. Attractive, low-profile design • Compact dispenser with undercounter storage extends only 22" (559mm) above counter • 12" (305mm) wide tower dispenses both ice and chilled water • Allows use in islands without restricting visibili

4 Specifications Electrical Each icemaker and dispenser require a separate circuit with with electrical disconnect within 10 ft (6m). Equipment ground required. Standard electrical – 115V, 60Hz, 1 phase. Maximum dispenser fuse – 15 amps, Maximum icemaker fuse – 20 amps each. Model Icemaker Dispensernumber amperage amperage VU155K series 11.0 amps ea 8.7 amps Plumbing Dispenser 3/4" PVC pipe nipple for bin drain 3/4" PVC pipe nipple for drain pan drain 1" ID hose for beverage bath drain Beverage

Check that ice is in the dispenser and that congealed cubes are not causing a jam. 2. Check that circuit breaker and switches are in ON position. 3. Check that drain pan, rear lid and top are on securely. If ajar, dispenser will not operate. When the top is off, auger does not operate, even though the solenoids do (page 16). 4. Check that all drains are clear. Note: For units equipped with Follett compressed nugget icemaker, see Icemaker Operation and Service Manual for service and troubleshooti

3. Connect syrup line #1 to rinse tank, pressurize tank to 20-50 psi, and dispense 3 gallons (11L) into a suitable container from valve #1. 4. Repeat this cleaning and rinsing for all syrup lines. 5. Remove diffusers and nozzles from valves, soak in cleaning solution, rinse well and reinstall. Sanitizing beverage lines Prepare 6 gallons (23L) of sanitizing Solution B. Fill a clean product tank with this solution. 1. Connect one tank to syrup line #1. Dispense 1/2 gallon (2L) from valve #1. 2. Re

Do not hang dispenser on flange. All dispensers must be installed level in both directions to ensure proper operation. 1. Check that dispenser location meets all requirements in this manual and cut counter as shown. Plan View Plan View units with up to 8 valves units with 10 valves counter cut-out counter cut-out Front of counter +.125" - .125"30.375" (772mm) +3 mm - 3 mm 26.25" +.125" - .125" (667mm) +3 mm - 3 mm 26.25" Front of counter +.125" - .125" +.125" - .125" 36.375" (924mm) +3 mm - 3 mm

Simultaneous flashing – the waterbath did not reach set temperature in 40 minutes. Reset this error mode by turning power off, removing top lid, drain pan or rear lid. Electrical box Front View I 0 I 0 I 0 power on/off switch #1 #2 icemaker warm/red LED bev. bath indicator cold/green LED probe switches 16 Replacement parts Dispenser exterior Top View Front View 8 valve (8v) unit with right hand (RH) tower 8 valve (8v) unit with right hand (RH) tower (push-button dispensing) 1 8 9 4 1 11 10 3 5 1

If problems persist after following this basic troubleshooting guide, call Follett’s technical service department toll at (800) 523-9361 or (888) 2-FOLLETT or (610) 252-7301. 15 Operational Status The chart below shows the operational status of various parts when certain switches are turned off or accessories are removed. Condition Pump Solenoids Auger Wheel Beverage valves Top lid off Rear lid off Drain pan off On/off switch in off position Beverage switch in OFF position OFF ON ON OFF ON ON ON

3. Remove auger motor assembly (see above). 4. Remove quick release pins from the ice chutes and gates, then unplug wires from solenoids. 5. Lift dispense mechanism up and off auger tube. Auger and auger tube removal (Fig. 3) 1. Remove auger motor and dispense mechanism assembly (see above). 2. Pull auger upward to clear auger tube. 3. Lift auger tube upward to clear dispenser top. 4. Slide tube and bearing plate through auger tube gasket. Dispense wheel removal 1. Remove drain pan assembly and