Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Fotos und technische Daten Jonsered FC 2145 |
Anleitung Zusammenfassung
Oiling the air filter Always use special filter oil. Filter oil contains a solvent to make it spread evenly through the filter.You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil. This would drain through the filter quite quickly and collect in the bottom. An air filter that has been in use for a long time cannot be cleaned completely.The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced. Bevel gear The bevel gear is filled with the right amount of grease at the factory. However, before using the machine you should check that the bevel gear is filled 3/4 full with grease. Use JONSERED special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out. Drive shaft The drive shaft must be greased every three months during full-time use. Contact your dealer if you are uncertain about the procedure. Spark plug The spark plug condition is influenced by: • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dirty air filter. These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties. If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm (0,020"). The spark plug should be replaced after about a month in operation or earlier if necessary. CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor. English – 29 MAINTENANCE Winter use Running problems can occur when using the machine in the cold and snowy conditions caused by: • Too low engine temperature. • Icing of the air filter and carburetor. Special measures are therefore often required: • Partly mask the air inlet on the starter to increase the working temperature of the engine. • Preheat the intake air to the carburetor by using the heat from the cylinder. Temperature 0°C (32°F) or colder: The air filter holder is prepared so it can be changed for use in the cold. Remove the air filter cover and air filter. Turn the winter cover anticlockwise using a screwdriver so that the preheated air from the engine can pass inside the carburettor compartment and prevent, for example, the air filter from icing up (see figure). For temperatures below -5°C (23°F) and/or in snow conditions there is also: •a special cover for the starter housing •a cover for cylinder cover’s air inlet should be fitted as illustrated. These reduce the cooling air and prevent large amounts of snow from being sucked into the engine. IMPORTANT! If the temperature rises above -5°C (23°F) or 0°C (32°F) respectively the machine MUST be restored to its normal set-up. Otherwise there is a risk of overheating, which can cause severe engine damage. 30 – English MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorised service workshop. Maintenance Daily maintenance Weekly maintenance Monthly maintenance Clean the outside of the machine. X Check that the harness is not damaged. X Make sure the throttle trigger lock and the throttle function correctly from a safety point of view. X Check that the stop switch works correctly. X Check that the cutting attachment does not rotate at idle. X Clean the air filter. Replace if necessary. X Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. X Check that the blade is correctly centred, is sharp, and is not cracked. An off-centre blade will cause vibration that could result in damage to the machine. X Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. X Check that the locking nut of the cutting equipment is tighten correctly. X Check that the locking screw is tightened when using a support cup with bearings. X Check that the transport guard for the blade is intact and that it can be secured correctly. X Check that nuts and screws are tight. X Check that there are no fuel leaks from the engine, tank or fuel lines. X Check the starter and starter cord. X Check that the vibration damping elements are not damaged. X Clean the outside of the spark plug. Remove it and check the electrode gap. Adjust the gap to 0.5 mm (.20”), or replace the spark plug...
Dieses Handbuch ist für folgende Modelle:Gartengeräte - FC 2145S (2.04 mb)