Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
c) Turn spout to center forward position and clamp cable to cable anchor on far side of spout using clamp (#84). 7. Mounting blower on tractor: a) Mount the blower on a tractor with a category 1 or category 2 hitch. b) Using tape or bright colored marking pen, mark on the outer shields the position where the shaft is completely pushed together and the position where you have a 4" overlap. Watch these marks when moving the blower through all possible operating angles to see that the PTO shaft stays within this range. c) With the engine on the tractor shut off, attach the PTO shaft. The tractor end has a standard 6-spline end with a spring loaded locking collar. The Snowblower end has a clamp-style yoke with a 3/8" keyway. Slide the yoke onto the gearbox shaft with the 3/8" key supplied. Lock the yoke in place with the .” x 3" hex bolt and lock nut fitted through the groove in the gearbox shaft. After tightening the bolt, insert and tighten the 3/8" socket set screw supplied. CAUTION : Always check to see that both ends of the PTO shaft are securely attached every time the Snowblower is used. This should always be done with the Tractor engine off. d) Check that the PTO shaft does not bottom or separate with the blower in the extreme high and low positions. A longer optional PTO shaft is available if the standard shaft is too short. Check for free movement of all parts in various raised positions; particularly the PTO shaft . ASSEMBLY INSTRUCTIONS – cont’d. 8. PTO Shield: All snowblowers are supplied with a PTO shield. Bolt the shield (#74) to the hinges on the top of the gearbox on both the #740 and #840 snowblowers using .” x .” hex bolts, lock washers and hex nuts. Insert a 3/16" cotter pin in the hole in the shield and in the hole at the bottom corner of the gearbox. Fold back the cotter pins to hold them in place. Hook the ends of the spring (#71) into these cotter pins to hold the shield down. To mount the shield (#74) on the #840G snowblower, remove the two rear bolts at the top of the gearbox (#63). Bolt the PTO shield to the gearbox plate using these same bolts. Insert a 3/16" cotter pin in the hole in the shield and fold to lock in place. Hook one end of the spring (#71) into this cotter pin and the other end into a hole in the lower gearbox plate to hold the shield in place. CAUTION: Do not run the snowblower without this shield in place. REFILLING GEARBOX WITH OIL: #840G ONLY If the gearbox requires refilling with oil because of repairs to the gearbox, add oil to the level shown in the drawing. Check the level regularly using the plug in the lid. The correct level is even with the bottom of the plug. 740 & 840 SNOWBLOWERS #840G SNOWBLOWER WHEN ORDERING PARTS Always give your dealer the Model, Color and Serial Number of your machine to assist him in ordering and obtaining the correct parts. Use the exploded view and tabular listing of the area of interest to exactly identify the required part. #740, #840, & #840G SNOWBLOWERS ITEM PART # DESCRIPTION 1 907241 Main Body (#740) 907235 Main Body (#840) 907240 Main Body (#840G) 2 907244 Stand Weldment - 8'' Tall 3 965294 Stand Pin Weldment 9/16'' x 2 7/8'' 4 F0463 Hitch Weldment (Category 1 & 2) 5 965803 Hand Crank 6 965653 Discharge Spout 7 965927 3/16'' Cable x 100'' Long 8 F842 PTO Shaft (Standard) F844 PTO Shaft (Optional Long) 9 907213 Btm Tube Weldment 20 5/8'' Lg 10 81676 5/8'' Hex Nut (pl) 11 81677 5/8'' Lock Washer (pl) 12 81620 1/2'' x 1 1/4'' Hex Bolt (pl) 13 81636 1/2'' Hex Nut (pl) 14 81637 1/2'' Lock Washer (pl) 15 81627 1/2'' x 3'' Hex Bolt (pl) 16 965821 3/8'' x 1 3/4'' Key 17 965806 3/16'' Cable Clamp 18 965807 Top Link Pin (Category 1) 19 965808 Top Link Pin Bushing (Category 1-2) 20 907214 A-Frame - LH (Category 1) 21 907215 A-Frame - RH (Category 1) 22 965911 7/16'' Linch Pin 23 84277 1/2'' x 1 1/2'' Hex Bolt (pl) 24 84072 3/8'' x 3/4'' Hex Bolt (pl) 25 81593 3/8'' Lock Washer (pl) 26 81592 3/8'' Hex Nut (pl) 27 81638 1/2'' B.S. Flat Washer (pl) 28 812026 5/16'' x 1'' Hex Bolt (pl) 29 967140 1'' x 10Ga Narrow Rim Washer (pl) 30 902377 Fan Key - 3/8'' x 4 3/4'' 965814 3/8'' x 4 1/4'' Key (#840G Only) 31 965835 Fan Shaft, 1 1/2'' x 16 3/4'' 32 965816 Bevel Gear - 1 1/4'' Bore 33 965817 Bevel Gear - 1 1/2'' Bore 34 965818 1 1/4'' Bearing w/ Collar 35 961637 Bearing Retainer (Set) 36 86170 3/8'' x 1'' Hex Bolt (pl) 37 901940 5/16'' x 1 1/4'' Key (#740 & #840) 38 965413 Drive Shaft (#740), 1 1/4'' x 37 1/4'' 965402 Drive Shaft (#840), 1 1/4'' x 42 1/4'' 965403 Drive Shaft (#840G), 1 1/4'' x 34'' 39 936402 PTO Safety Chain 40 81527 1/4'' x 1'' Hex Bolt (pl) 41 84498 1/4'' Lock Nut (pl) 42 968627 1 1/2'' Bearing With Collar 43 967260 1 1/2'' Bearing Retainer (Set) 44 965822 Fan (Standard 3-Blade) 965447 Fan (Optional 4-Blade) 45 965414 Auger (#740) 965405 Auger (#840 & #840G) 46 965415 Drive Shaft Guard (#740) 965404 Drive Shaft Guard (#840 & #840G) 47 907218 Hitch Tube Weldment 22''Lg 48 965834 Idler Spacer, 5/8'' Long 49 84111 1/2'' x 1 1/4...