Provisions for adequate combustion and ventilation air must be provided. Refer to page 7. WARNINGS If the information in this manual is not followed exactly, a fi re or explosion may result causing property damage, personal injury or loss of life. – Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance. – WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your

. . . . . . . . . . . . . . . . . . . . . . . . . 19 Lighting Instructions – Millivolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Lighting Instructions – Electronic ...........................24 Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Troubleshooting Guide – Millivolt. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Troubleshooting Guide – Electronic. . . . . . . . . . . . . . . . . . . . . . . . . . 28 Replacement

Framing dimensions in illustrations accommodate 1/2" finishing material. A Brand of Monessen Hearth Systems Co. 149 Cleveland Drive, Paris, Kentucky 40361 To avoid personal injury or property damage, the product described by this brochure must be installed, operated and maintained in strict compliance with the instructions packaged with the product and all applicable building or fire codes. Contact local building or fire officials about restrictions and installation inspection requirements.All p

A spacious viewing area and a modest footprint make this dependable unit easy to install, operate and service. Available in dedicated rear or top vent formats. STANDARD FEATURES FOR ALL UNITS: • Direct Vent Gas Fireplace • Clean viewing area • Flat louvers • Standard 36" size • New black embossed refractory comes as standard • Gas inlet flex line with shut-off valve • Includes electrical receptacle • Attached 17" low voltage wire connected to valve for remote operation hook-up • 2 piec

• The installation must conform with local codes or, in the absence of local codes with the National Fuel Gas Code, ANSI Z223.1. • The heater and its individual shut-off valve must be disconnected from the gas supply piping system while performing any tests of the gas supply piping system at pressures in excess of 1/2 psig. • The heater must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at

If your mantel profile is unsafe, you may either: • Raise the mantel to an acceptable height, or • Remove the mantel. Floor clearance: These fireplaces may sit directly on a combustible surface. ASSEMBLY STEPS Note:Illustrations shown in this manual reflect “typical” installations with nominal dimensions and are for design and framing reference only. Actual installations may vary due to individual design preferences. However, always maintain minimum clearances to combustible materials and do not

Once a small hole has been made, continue tapping until you have reached sufficient diameter for the gas line to fit through. The entire knockout does not have to be removed. Install only a ..." (1 ..." max.) inside diameter approved gas line through the firebox wall for connection to the unvented room heater inside the firebox. Ensure that a sediment trap is installed in the existing gas line, if not, install a sediment trap upstream of the heater to prevent moisture and contaminants from passi

Btu Input: 40,000 BTU/HR Ignition System: Standing Pilot or Signature Command™ System Gas Type: Natural or LP Flue Type: Simpson Dura-Vent, Selkirk Metalbestos, MetalFab Termination: Top vent Clearance to Flue for Interior: 3" Top 1" Bottom and Sides Clearance to Flue for Outside Wall: 1" Clearance to Fireplace: 1" Minimum Vent Height Before Elbow: 24" CSA Design Certified FIELD INSTALLED ACCESSORIES Variable Thermostat Controlled Dual Forced Air Blower (160 cfm): BLOTKHL Firebrick: Cott

Btu Input: 50,000 BTU/HR Ignition System: Standing Pilot or Electronic Gas Type: Natural or LP Flue Type: B Vent Vent Size: 8" B Vent Clearance to Flue: Specified by B Vent Manufacturer Clearance to Fireplace: 1/2" CSA Design Certified FIELD INSTALLED ACCESSORIES Bi-fold Glass Doors (Required on Propane Models): BBD4536 (Polished Brass), BLD4536 (Black) Cottage Clay firebrick Cottage Red firebrick Ambient Technologies™ Remote Controls and Thermostats -45"- -36"- _c 4-1/2" 45-1/4"

The hood kit replaces the standard hood that comes with these appliances and snaps into place. These kits can be retrofitted to previously installed appliances. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. ACCESSORY COMPONENTS CONTINUED Door Frame Kits (2-Piece, Top and Bottom) Two types of decorative door frame kits are available for use with these appliances - one, in polished brass finish; the other, in brushed stainless steel finish. The DTK is designed to attach directly to the front face o