11. DO NOT BURN OR INCINERATE BATTERY PACKS. Battery packs may explode, causing personal injury or damage. Toxic fumes and materials are created when battery packs are burned. 12. DO NOT CRUSH, DROP, OR DAMAGE battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over, or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped on). 13. DO NOT DISASSEMBLE. Incorrect reassembly may result in the risk of electric shock, fire or exposu

14. Use this product in accordance with the battery’s and vehicle’s instruction manual recommendations, safety warnings and charging instructions. 15. Never leave Battery Charger unattended. 16. Batteries can explode under certain conditions; excessive heat and/or poor ventilation can cause explosive gas buildup and battery explosion. Surges in electrical power supply could possibly cause battery explosion. Battery Charger should be plugged into a surge protection device. SKU 45005 For technical

Controller 10 If the Vendor ID, Device ID, Device Class or IRQ aren’t displayed or an error occurs, please try another PCI slot. Once the hardware has installed correctly you can start installing the software from the driver CD. Pin Assignments Parallel 25 Pin female connector pin assignments: Parallel 25 Pin female connector : Pin Signal Pin Signal Pin Signal 1 STROBE 10 ACKNOWLEDGE 19 GROUND 2 DATA 0 11 BUSY 20 GROUND 3 DATA 1 12 PAPER EMPTY 21 GROUND 4 DATA 2 13 SELECT 22 GROUND 5 DATA 3 14 A

Further, the Mach! Lightning can charge two of Lenmar's PROH cells in as little as 8 minutes or four PROH or high quality standard NiMH cells in as little as 15 minutes. The Mach 1 Lightning SpeedCharger features microprocessor controlled NeoTherm®2 Active Pulse Speedcharging to charge your battery quickly and safely. This charger will charge one to four batteries at a time, each with a dedicated LED indicator to show the charge status of that individual cell. Flexible power input allows you t

There are3 phases to tha dwga cycle. The battery may ba removed difhg any of tha с hug big phases without ham) to the battery or charger unit a I - Iddd Creaget Al 3 LED"* fahlng In sequaiKa from MED (Irft) to MAX [right) 0 dbg.-2). If the battery b tow, thh wll be the frst charge phase. WKh high capedty batterietthb phtne can sometfcna be the longest of the 3 phases. Sin I art* arfth tame bn ehtog thn md o/thrfr ll^thta phu» can ba wry «horr. LED's SCOLIE^TIAL I SEQUENTIAL SCOUEKTUkl PHASE I

3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2009 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual p

32571, 2 Port LINDY No. 32572, 4 Port LINDY No. 32573, 8 Port © LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH – SECOND EDITION (Jun 2007) Manual English Single Stage Installation In a single stage installation no additional video splitters are daisy chained down from the first unit. To set up a single stage installation, do the following: 1. Use a high quality HD 15 Male/Female video extension cable to connect the PC’s video port to the ‘VIDEO IN’ port of the video splitter. 2. Use high qual

The Mach 1 Speed Charger features microprocessor controlled NeoTherm® active pulse speedcharging to charge your battery up to 7 times faster than other standard chargers. Not only will it charge the battery safely and reliably, it will prolong battery life. Unlike the other “60 minute” chargers, the Mach 1 will not overheat the batteries and damage them. The Mach1 Speed Charger actually prolongs battery life. 1 to 4 batteries can be charged at a time, each with a dedicated LED indicator to show

As many video splitters as ports are available on the highest level splitter can be chained. 2, 4 and 8-port models can be mixed on the same chain. Theoretically there is no limit to the number of levels in the chain but be aware that the signal quality may deteriorate as you chain further and further away from the video signal source. Note: If you connect a DDC type monitor to ‘VIDEO OUT’ port No. 1, all other monitors must be able to support the highest resolution that the DDC monitor can prov

Schneiden Sie das Schirmgeflecht, bzw. Schirm- und Kunststoffolie so ab, dass noch ca. 10 mm unter dem Kuststoffmantel hervorschauen. Wickeln Sie den Beilaufdraht um die verbleibenden 10mm Schirmung, er wird spater unter der Schelle mit festgeklemmt Falls vorhanden, kurzen Sie die Schirmfolie der Maximal 13 mm entdrillen einzelnen Paare (PiMF-Kabel) auf die gleiche Lange. Entdrillen Sie die Paare maximal auf eine Lange von 13mm und legen Sie die Adern nach dem vorgegebenen Farbschema auf. Verwen