Consult a physician before beginning any exercise program with this equipment. If you feel faint or dizzy, immediately discontinue use of this equipment. Serious bodily injury can occur if this equipment is not assembled and used correctly. Serious bodily injury can also occur if all instructions are not followed. Keep others and pets away from equipment when in use. Always make sure all bolts and nuts are tightened prior to each use. Follow all safety instructions in this manual. When calling f

Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws. 3/16" 1/4" 5/16" 3/8" 1/2" INCHES mm. in. 11/20 21/2 31/2 41/2 51/2 61/2 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 MILLIMETERS 6810 12 NOTICE: The length of all bolts and screws, except those with flat heads, is measured from below the head to the end of the bolt or screw. Flat head bolts and screws are measured from th

Connect the PULSE EXTENSION WIRE(40) to the CONTROL WIRE(24). Insert the REAR FRAME(5) onto the FRONT FRAME(1) and secure with BUTTON HEAD BOLTS(M10x1.5x20mm)(66), BUTTON HEAD BOLTS(M10x1.5x53mm) (67), ARC WASHERS(M10)(87), LOCK WASHERS(M10)(89), WASHER(M10)(92), and ACORN NUT (M10x1.5)(85). NOTE: See page 13 for detailed leveling instructions to prevent rocking. ASSEMBLY INSTRUCTIONS 9 B. A. (Assembled at the factory) STEP 5 Refer to illustration A. Attach the HANDRAIL(8) to the SEAT FRAME(7) w

10 SET UP INSTRUCTIONS Place the CPS 9200 Indoor Cycle in the area where it will be used. It is recommended that the CPS 9200 Indoor Cycle be placed on an equipment mat. The CPS 9200 Indoor Cycle is approximately 50 inches long (max.) x 18 3/8 inches wide x 42 5/8 inches tall (max.). An area 4 feet wide x 6 feet long is required for safe operation of the CPS 9200 Indoor Cycle. Make sure that adequate space is available for access to and passage around the CPS 9200 Indoor Cycle. Adjust the STANDS

There are no other warranties other than those expressly set forth herein. Products shipped to the manufacturer must be in the original shipping carton with freight prepaid. All expenses for repairing or replacing the product, including the cost of shipping it back to the original purchaser, will be covered by the manufacturer. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. 3 4 DIAGRAM# PART NAME QTY 1 Main Frame 1 2 Stabilizer 2 3 St

(These dimensions may vary up to one inch.) An area 4 feet wide x 6.5 feet long is required for safe operation of the Air Fusion 4525 Bike. Make sure that adequate space is available for access to and passage around the Air Fusion 4525 Bike. LEVELING: MOVING: FUNCTION INSPECTION: Visually inspect the Air Fusion 4525 Bike to verify that assembly is as shown in the above illustration. Check the function of the Air Fusion 4525 Bike by turning the crank slowly through one complete revolution to veri

Stamina Products will arrange to pick up the Inversion Table and offer you a replacement or refund. If you have any questions regarding this recall, you may call 888-STAMINA (888-782-6462).

If just starting an exercise program, work out at the low end of your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your workout by increasing your heart rate. Measure your heart rate periodically during your workout by stopping the exercise but continuing to move your legs or walk around. Place two or three fingers on your wrist and take a six second heartbeat count. Multiply the results by ten to find your heart rate. For example, if your six se

NOTE: STEP 3: Make the tab in the edge of the OVAL ENDCAPS(58) face down, then press the OVAL ENDCAPS (58) into both ends of the front stabilizer of the MAIN FRAME(1). R L ASSEMBLY INSTRUCTIONS 8 STEP 5 CAUTION: Attach the UPRIGHT(3) to the MAIN FRAME(1) with the NYLOCK NUTS(M10x1.5)(84) and WASHERS (M10)(78). Plug the BASE CONNECTION WIRE(18) into the CONNECTION WIRE(19). STEP 6 Connect the LINKS(36) to the ROCKER ARMS(4) at both sides with D-SHAPED SHAFT(42), WASHERS (M6)(77), and BUTTON HEAD

The minimum program time value is 20:00 minutes. Use the UP and DOWN buttons to set the program time from 20 minutes up to 99 minutes in one minute increments. When desired time is displayed press the SET button. The TIME will count down from preset value. 1. 2. STEP 4: Now you are ready to begin exercising. The program will not start until you start pedaling. 15 If two blocks are displayed, your speed is within the acceptable range. If only one block is displayed in the center, your speed match