(1) 25 06-42-1600 Woodruff Key (1) 26 32-40-1581 Intermediate Gear (1) 27 40-50-6300 Shifting Spring (2) 28 44-70-0100 Shifting Plunger (2) 29 32-60-2011 Pinion Gear (1) 30 45-88-0520 Thrust Bearing Washer (1) 31 02-80-1800 Thrust Bearing (1) 32 32-10-0061 Clutch Gear Assembly (1) 33 06-42-2000 Woodruff Key (1) 34 36-14-0061 Clutch Shaft (1) 35 45-88-0530 Thrust Bearing Washer (1) 36 02-80-5000 Thrust Bearing (1) 37 32-10-0051 Clutch Gear Assembly (1) 38 45-88-0510 Thrust Bearing Washer (2) 39 0

Step 2 Install the leveling screws (8), screwing four (4) into each base. Step 3 Install the feed handles (1) and knobs (2) by screwing one knob onto the end of the handle, then slip thru hub and attach other knob. Step 4 Remove the Manta from the vacuum base by removing the nut and bolt that holds the main assembly to the vacuum base. Set the Manta aside, observing the following precaution. Turn the vacuum base over. Press the gasket into the groove in the underside of the base. The gasket is c

13135 WEST LISBON RD. BROOKFIELD, WIS. CRIMP LEAD 3 AND LEAD 7 TOGETHER IN T1 BEFORE INSERTING INTO SWITCH. CRIMP LEAD 4 AND LEAD 8 TOGETHER IN T1 BEFORE INSERTING INTO SWITCH. INSERT TERMINALS T2 ON LEADS 5 AND 6 INTO BRUSH HOLDER BEFORE ROUTING THRU WIRE TRAPS. ___, , TUCK LEADS 7 AND 8 DOWN INTO THE ----- WIRE TRAP UNDER SWITCH. BULLETIN 58-03-0475 TUCK LEADS 3 AND 4 DOWN INTO THE WIRE TRAPS BETWEEN SWITCH AND FIELD. WIRING SPECIFICATIONS Wire No. Wire Color Origin or Gauge Length

Reattaching the locator assembly will not change the depth setting. Driving Self-Drilling Screws intoCold-Formed Steel Framing (Fig. 13)For Adjustable Torque ScrewdriversRated 0-2500 RPM Follow this procedure when working with light gauge sheet metal, 20 gauge and thicker. The screw may hesitate slightly when it finishes breaking through the first layer of material and starts to penetrate the sheet metal. This is normal. Keep fi rm pressure on the tool until the screw is fully seated. Self-drill

13135 WEST LISBON RD. BROOKFIELD, WIS. Route red brush assembly leadwire #2 through wire traps as shown. DATE Mar. 2010 BULLETIN 58-01-1830 ROUTE THE LEADWIRES BETWEEN THE POSTS. Black leadwire #5 Black leadwire #6 NOTE: On some early models, leadwires #3 and #4 may be red. Later production and service replacements are white. White leadwire #4 WIRING SPECIFICATIONS Wire No. Wire Color Origin or Part No. Gauge Length Terminals, Connectors and End Wire Preparation 1 Black 22-18-1

Use only specifically recommended accessories. Others may be hazardous. Removing and Replacing Quik-Lok® Cords (Fig. 1) Cat. No. 9072-20, 9072-22, 9092-20 and 9096-20 MILWAUKEE's exclusive Quik-Lok® Cords provide instant fi eld replacement or substitution. Fig. 3 Drive shank Fig. 1 1. To remove the Quik-Lok® Cord, turn the cord nut 1/4 turn to the left and pull it out. 2. To replace the Quik-Lok® Cord, align the connector keyways and push the connector in as far as it will go. Turn the cord nut

Fig. 6 Forward Reverse Forward/ Reverse Switch 1. For forward (clockwise) rotation, push the forward/reverse switch in the direction shown. Check the direction of rotation before use. 2. For reverse (counterclockwise) rotation, push the forward/reverse switch in the direction shown. Check the direction of rotation before use. WARNING To reduce the risk of injury, keep hands and cord away from the bit and all moving parts. WARNING To reduce the risk of explosion, electric shock and property damag