220V -10.5 ohms approx. 240V -13 ohms approx. If all readings are not correct, replace elements as needed. Oven heats with switch off Mercury Contactor(s) The mercury contactor has probably malfunctioned in the closed position. If there is no voltage to the operating coil, but there is high voltage at the contactor output, replace the mercury contactor. Conveyor will not run (S/N 100-4389) Voltage Supply Check incoming voltage supply at line 1 to neutral. There should be a voltage reading of 120

The direct drive conveyor is powered by a DC motor. The fuses for the controls and blower motor are located on the side of the control box. 1111 North Hadley Road P.O. Box 1229 Fort Wayne, Indiana 46801-1229 Tel 1.260.459.8200 Fax 1.260.436.0735 E mail info@lincolnfp.com web Enodis- mpinger® Countertop Oven L incoln 32" (813 mm) (1270 mm) ELECTRICAL SERVICE: Heat is supplied by one (1) element at 5600 watts. Each oven is rated at 6kW. The ovens are available in 208V and 240V and are si

Handles flux-cored welds on mild steel with ease. Practically everything you need to MIG weld mild steel is right in the box. Unit includes: • 4-Step Tap voltage control • Magnum® 100L welding gun and 10ft. (3m) cable assembly, with gas nozzle, .023” - .035” (0.6–0.9mm) cable liner and .023/.025” (0.6mm) contact tip • 10ft. work cable & work clamp • 6 ft input power cord with NEMA Type 5-15P plug • Guide tubes and reversible drive roll for .023-.035" solid MIG wire and .035" Innershield® flux-co

If thermostat will not hold, and control box temperature is not exceeding 140°F (60°C), replace thermostat. Power switch Check continuity between switch terminals. Replace switch as needed. Control transformer Check for 120 VAC supply to the primary of the control transformer. If no voltage is present, trace wiring back to the oven power relay. If voltage is present, check for 24 VAC at the transformer secondary. If there is primary voltage but no secondary voltage, replace control transformer.

GAS / 120 VAC / 60 HZ / 1 PHASE POWER SUPPLY Electrical power is supplied to the oven by a three conductor cordset. Voltage from the black conductor to the white conductor is 120 VAC. The white conductor is neutral. The green conductor is ground. CONTROL BOX AUTO When the temperature in the control box reaches 120°F ± 3° (48.9°C ± 1.7°C), the COOL DOWN interrupt power to the fans when the control box temperature falls to 100°F ± 3° (37.8°C ± 1.7°C). MAIN FAN CIRCUIT Power is permanently supplied

The AC-225C can be used for many welding applications such as maintenance repairs, fabrication, modifying equipment, and creating or rebuilding tools, fixtures, or worn parts. Features: • Easy Installation • Input power cable and plug included Easy to Operate • Electrode holder and cable, work clamp and cable, sample electrodes, welding helmet and welder's guidebook all included • Easy to use controls •Convenient size to allow easy storage and handling • 3 year warranty including parts and labor

B. To adjust the temperature offset, access the OFFSET display in the Sub Set Point Menu. If cavity temperature is above the set temperature, decrease (down button) the offset value. If cavity temperature is below the set temperature, increase (up button) the offset value. The amount of offset needed should be the difference between the cavity temp. and the set temp. Allow oven to reach set temp. and verify cavity temperature. Readjust offset as necessary. C. HI TEMP and LOW TEMP are not normall

Specifications and availability of optional features may have changed. Shipping Damage Claims When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, claims for material damaged in shipment must be made by the purchaser against the transportation company at the time the shipment is received. Safety Depends On You Lincoln arc welding equipment is designed and built with safety in mind. However, your overall safety can be increased by proper ins

Slide the guide tube up against the installed drive roll. 9. Install the second drive roll on the remaining shaft the same way as the first. Center the middle guide tube between the rolls and tighten the thumbscrews holding it in place. 10. Close and latch both quick release levers. 11. Slide the longer guide tube into the rear hole of the gearbox until it almost touches the drive roll and guide tube. Tighten the thumbscrew to hold it in place. 12. Install the outgoing guide tube into the front

Setting the oven control to the desired time outputs voltage, through a reversing switch, to the conveyor motor. NOTE: The conveyor system uses a hall effect sensor and magnet to prove operation of the conveyor motor. If the conveyor motor is not running, “BELT JAM” is indicated on the display. AUTOMATIC COOL DOWN When the oven is started, the time delay relay timing circuit is enabled, permitting the oven fans to run approximately 20 minutes after the oven is shut off, to cool the oven. The tim