• 2.11.7 ELECTRICAL SYSTEM Make sure the generator is properly connected to an approved earth ground and/or ground rod. Section 3 - Operation Guardian 40kW Liquid-cooled Generators Make sure the generator battery is fully charged, properly installed and interconnected, and ready for use. Check to ensure that there are no loose electrical connections. Restrain any loose wires to keep them clear of any moving generator set components. 3.1 USING AN ENGINEERED “GTS” TRANSFER SWITCH When required, th

CB TERMINAL COVERS IS SUPPLIED WITH CIRCUIT BREAKERS. (2) 2/3 QTY. 2 POLE & 3 POLE CB. 1 0G0056 0G1155 0F9677 0G0959 2 0G0057 0F9664 0G0058 0G0184 0G0059 0G0183 3 0C9708 4 SEE ENGINE EV 5 SEE ENGINE EV 6 0F5767B 7 0E5706 8 0F7874 9 0G0587 10 038150 11 023454 12 077043F 13 04576100BU 14 052646 15 043123 16 051779 17 0A2601 18 0A2602 19 0F8408 20 046526 21 0C3993 22 022264 23 * 047248 24 * 070892 25 0G0588 1 RTR-2390--35KD1 CPL 1 RTR-2390--35KD1 CPL (G2) 1 RTR-2390--45KD1 CPL 1 RTR-2390--45KD1 CPL

005040-0, 005040-1 (25kW) 005053-0, 005053-1 (20kW) 005054-0, 005054-1 (15kW) This manual should remain with the unit. ONLY QUALIFIED ELECTRICIANS OR CONTRACTORS SHOULD ATTEMPT INSTALLATION!! INTRODUCTION Thank you for purchasing this model of the Guardian Elite standby generator series by Generac Power Systems, Inc.. Every effort was expended to make sure that the information and instructions in this manual are both accurate and current at the time the manual was written. However, the manufactu

This booklet should only be used in conjunction with the Owner’s Manual, Installation Guide and other technical documents shipped with your equipment. Future product updates and/or modifications will be reflected in the written documentation included with your equipment. Always read all accompanying documentation carefully before attempting to install any generator, transfer switch or related equipment. It is essential to comply with all regulations established by the Occupational Safety and Hea

17 042558 1 KEY SQ 3/8 X 1 STEEL 18 0A5061 1 SPACER-FLEX PLATE 19 0A4989 1 PLATE, FLEX 20 053557 1 SCREW HHC M12-1.75 X 40 G8.8 21 051769 6 WASHER LOCK M12 22 049541 4 SCREW HHC M10-1.5 X 35 G8.8 23 046526 4 WASHER LOCK M10 24 045772 4 NUT HEX M10-1.5 G8 YEL CHR 26 * 087599 1 PLUG PLASTIC 3/8 NPT 27 077043E 1 FLEX CONDUIT 1" BLACK (NOT SHOWN) 28 022131 4 WASHER FLAT 3/8-M10 ZINC 29 072578 1 SPACER ROTOR SHAFT 30 0A7043 5 SCREW HHC M12-1.25 X 25 G8.8 31 049808 5 WASHER FLAT M12 32 058589 1 DECAL

3 Section 1 – General Information .................................4 1.1 Unpacking .............................................................................4 1.1.1 Accessory Box ........................................................4 1.2 Assembly .............................................................................. 4 1.2.1 Assembling the Wheel Kit ....................................... 4 1.2.2 Assembling the Handle ...........................................4 1.2.3 Battery Connec

! Gaseous fuels such as natural and LP (propane) gas are highly explosive. Even the slightest spark can ignite such fuels and cause an explosion. No leakage of fuel is permitted. Natural gas, which is lighter than air, tends to collect in high areas. LP gas is heavier than air and tends to settle in low areas. ENGINE PROTECTIVE DEVICES The engine has several safety switches which cause the engine to automatically shut down under the following conditions: low oil pressure, high coolant temperatur

In the air-cooled product this offers rodent and insect protection which could potentially be an issue during service intervals. In liquid cooled product, it completes the look of a finished base for a sleek, streamlined appearance. Please note that the base plug kit (5652) for the air-cooled product only fits air-cooled units manufactured prior to 4/2008 that do not have the contoured body wrap style. DESCRIPTION: The enclosure is the generator's first line of defense against the elements an

Be sure to read the “Safety Rules”, as well as all other safety information in this manual, before attempting to operate this (and related) equipment. Before starting the generator for the first time, the installer must complete the following procedures. For follow-up maintenance information and/or service intervals, please refer to the “Maintenance” section and the “Service Schedule”. • TRANSFER SWITCH If this generator is used to supply power to any electrical system normally powered by an ele

CAP HEX 1/4 NPT BRASS 1 DUCT INNER DISCHARGE TOP C2 13 SCREW THF M6-1 X 16 N WA Z/JS 4 SCREW HHC M8-1.25 X 20 G8.8 12 WASHER LOCK M8-5/16 4 WASHER FLAT 5/16-M8 ZINC 10 WASHER LOCK M6-1/4 8 SCREW HHFC M6-1.0 X 20 G8.8 4 SCREW HWHTF M6-1.0 X 16 1 DUCT INNER DISCHARGE C2 1 BRKT COOLANT RECOVERY TANK 1 TANK COOLANT RECOVERY 1 CLAMP HOSE BAND 1/4 3 INSULATION INNER DUCT 1 INSUL DUCT SIDE OR INNER DUCT 3 RETAINER INSULATION (450) 2 RETAINER INSULATION (220) 10 INSULATION RETAINMENT HANGER 10 WASHER SE