1). The burner will light. DO NOT operate the heater in any other than the full “ON” position. 9. IMPORTANT: DO NOT attempt to adjust the main burner input using the main gas supply valve, for this may cause the pilot and thermocouple to shut down the burner (Fig. 2). Shut-down instructions: To turn the heater OFF, • For short periods of time, turn the main burner off by rotating the gas valve knob clockwise to the “PILOT” position. • For extended periods of non use, turn the appliance completel

Gas pressures are shown in the table below. GAS TYPE GAS PRESSURE TABLE SUPPLY PRESSUREMANIFOLD PRESSURE High Low Minimum* Maximum Natural Gas 3.5” W.C. 1.4” W.C. 5” W.C. 14” W.C. Propane Gas 10.0” W.C. 4.0” W.C. 11” W.C. * Minimum permissible gas supply pressure for purpose of input adjustment. 14” W.C. –30– Form #43343530 JJuly 08 /C > / $8#1%<;"->#86%4>/, > / $8#1%<;"->* N -/ &$'* / &3',0/+/C4+/ DD /-,7!/"**"!,4/,+."+.

WE RESERVE THE RIGHTT0 ALTER ANY SPECIFICATION WITHOUT NOTICE. ITEM* PART NO. DESCRIPTION 29 42741040 Restrictor Plate, 1” I.D. (40M Btu/hr) 30 42741030 Restrictor Plate, 1-1/8’ I.D. (50M Btu/hr) 31 42741020 Restrictor Plate, 1-7/32” I.D. (60M Btu/hr) 32 42741010 Restrictor Plate, 1-7/16” I.D. (75M Btu/hr) 33 42741050 Restrictor Plate, 1-1/2” I.D. (80M & 90M Btu/hr) 34 42741060 Restrictor Plate, 1-5/8” I.D. (100M Btu/hr) 35 42741070 Restrictor Plate, 1-3/4’ I.D. (110M & 120M Btu/hr) 36

14.0”w.c. 21,000 18.500 28,000 This appliance may be installed in an aftermarket* manufactured (mobile) home, where not prohibited by state or local codes. This appliance is only for use with the type of gas indicated on the Rating Plate. This appliance is not convertible for use with other gases. *Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer. 28Z\x" (724mm) 24" (610mm) 3" (76mm) 14Z\x" (368mm) CL 8" (203mm) Valve Inlet 3447 Fig. 1 Jefferson Vent Free dimensi

Modern construction standards have resulted in homes that are highly energy-efficient and that allow little heat loss. Your home needs to breathe, however, and all fuel-burning appliances need fresh air to function properly and safely. Exhaust fans, clothes dryers, fireplaces and other fuel burning appliances use the air inside the building. If the available fresh air supply is insufficient to meet the demands of these appliances, problems can result. The JUVS heater has specific fresh air requi

—Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. —WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas suppler from a neighbor’s phone. Follow the gas suppler’s instructions. • If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, servi

Left Burner Leg Injector Orifices ST353a Fig. 19 Be sure injector orifices remain at 90° to the base. 5. Replace left and right log bracket assembly, tighten rear log bracket, and replace logs. 6. Latches provided in catalyst kit must be installed on top of firebox. Use two phillips screws to secure in place. (Fig. 20) Phillips Screws Phillips Screws ST671 Fig. 20 Attach glass latches. Catalyst Location 7. Slide catalyst between top plate and firebox. Allow catalyst to “fall” into hole on top of

Tube less Flanges (Hot Rolled) 1 1 3 3 41932051 5 Ft. Tube less Flanges (Hot Rolled) -2 -2 43319100 Reflector, 9’ 11.” 2 2 4 4 43319050 Reflector, 4’ 11 .” -2 -2 30462980 Tube Coupling 1 3 3 5 43318000 Tube Hanger/Support Bracket, 13” 2 4 4 6 43980010 Wire Hanger 2 4 4 6 Form #43343330 May 08 –7– Body Fastener Kit (included in body packages) 42907190 42907210 42907210 42907221 42873000 U-Bolt 2 4 4 6 02127110 Hex Nut, 5/16-18 5 8 8 13 02189020 HWHSM Screw, #10-16 x .” TEKS 8 14 14 24 U-Bend Pack

Option 1 - Vents to Adjoining Rooms Option 3 - Vents to Adjoining Room Option 2 - Remove Door to Adjoining Room VO370-2 Fig. 5 Supplementing ventilation air. Wall 10” 12” 8” 6” 4” 2” 10” 8” 6” 4” 2” 1” Wall 10” 12” 8” 6” 4” 2” 10” 8” 6” 4” 2” 1” Vermont Castings Jefferson Vent Free Gas Heater Clearance Requirements Hearth Requirements Minimum Clearances to Combustible Materials The JUVS must be installed on rigid flooring. If the appliance is installed on any combustible surface other than wood

d) If the meter reads less than the minimum or if reading is unsteady: .. Make sure burner flame is capable of providing a good rectification signal. .. Make sure fasteners securing igniter/sensor are tightened to assure correct positions. DO NOT relocate igniter/sensor. .. Check for excessive (over 1000.F) temperature at ceramic insulator on flame sensor. Excessive temperature can cause short to ground. DO NOT relocate igniter/sensor. .. Check for cracked ceramic insulator, which can cause shor