1 Safety Controls Operation Maintenance Troubleshooting Specifications Safety Rules & Information Safety Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Do not operate this machine unless you have been trained. Reading and understanding this operator’s manual is a way to train yourself. Power equipment is only as safe as the operator. If it is misu

Electrical safety Check the power cord regularly for damage and signs of wear and tear. Do not use your Turbotrimmer if the power cord is damaged. v If the mains cord or extension cable is damaged while you are working, unplug the mains plug immediately. Do not touch the cable until the mains plug is switched off. The socket of the extension cable you are using must be waterproof. v Only use permitted extension cables. v Ask your electrician. For all portable units that are operated outdoors we

v Insert the key into the socket. Circuit breaker has been triggered (Red Error-LED flashes). v Wait approx. 5-10 minutes then turn on the mower again. Tab on Accu loose. v Open the cover and push the tab receptacle onto the tab. Full discharge protection has responded. v Charge Accu. Motor jams and is noisy Blocked by foreign body. Blocking protection activated. (Red Error-LED flashes). 1. Switch off mower, 2. Remove key. 3. Remove foreign body. Cutting load too high. v Reduce mowing speed and

Date: 8/2004 TP 100-7131-02-UB-F Table of Contents Safety Rules & Information ................................2 Identification Numbers .......................................7 Features & Controls............................................8 Control Functions....................................................8 Safety Interlock System ..........................................9 Operating the Walk Behind Mower ..................10 General ...........................................................

2. Unscrew the reservoir cap (B, Figure 11). 3. Look down the filler neck of the hydraulic oil reservoir (A, Figure 11) and observe the oil level. When cold, the oil level should be level the baffle inside the reservoir (steel tank) or approximately 1/2” (1,2cm) below the “FULL HOT” line (plastic tank). 4. If necessary, add either Mobil 1™, 15W-50 synthetic oil or Castrol Syntec™ 5W-50 oil. DO NOT use conventional oils. 17 WARNING Gasoline is highly flammable and must be handled with care. Never

Nos.: 5901035 (S/N: 1023 & Above) (H3225K) 5901036 (H3227K) © Copyright 2005 Ferris Industries. All Rights Reserved. 29TP 400-7095-04-H3-F Deck Lift Group NOTE: Unless noted otherwise, 095DLT0 use the standard hardware torque specification chart. The above parts group applies to the following Mfg. Nos.: 5901035 (S/N: 1023 & Above) (H3225K) 5901036 (H3227K) © Copyright 2005 Ferris Industries. All Rights Reserved. 30TP 400-7095-04-H3-F Deck Lift Group REF NO PART NO. QTY. DESCRIPTION 1 5020959 1 R

48550 For Derby Pacer 1334 Kit Contents: Ref Part No. Qty. Description A. 1724832 1 MULCH PLATE B. 1724457 1 34” BAFFLE C. 1923362 1 NUT, Hex Lock, 5/16-18 D. 1679163 1 WING NUT E. 1724475 1 J-BOLT F. 25127 5 NUT, Serrated Flange, 5/16-18 G. 1931333 5 CARRIAGE BOLT, 5/16-18 3/4 O ii /• i ~ A fr "'n -V t'r"} y / Figure 1. Kit Components © Copyright 2003 Ferris Industries. All Rights Reserved. 1 48551 Rev. 01/2003 TP 200-7115-00-SK-D Installation Instructions 34” Mulching

9 GB Adjusting the cutting height: 566 The cutting height can be set to any position between 12 mm and 42 mm. 1. Stand behind the cylinder mower with one foot on the roller 5. 2. Release the two locking screws 6 and adjust to the correct height in the inspection window 7. 7 3. Tighten the two locking screws 6 on both sides to the same height. The locking screws 6 must always be set to the same height on both sides. The mower may only be adjusted to a depth in which the lower blade does not touch

keit erst nach mehreren Lade- A Vor dem Einstellen oder Saubern ist der Motor- Ist der Accu vollig entladen, maher auszuschalten und z. B. durch lang andauernde gegen unbeabsichtigtes Ein- Lagerung ohne zwischenzeitschalten zu schutzen. Dazu ist liche Nachladung, dann ist der Schlusselschalter Q aus die volle Accu-Kapazitat erst der Kontaktbuchse des Motor- nach mehreren Lade- / Entlademahers zu ziehen. vorgangen wieder verfugbar. 7.2 Der Accu (Abb. E/ G) Laden des Accus temperatur oder Aufheizu

Secure the fuel supply hose to the frame rail, making sure not to contact the pump cooling fan. 5. Reinstall the cross bar and mounts onto the new tank and secure with the saved hardware. 6. Reinstall the bumper and secure with the saved hardware. A. 3/8” x 1-1/4” Bolts E. B. 3/8” SAE Washers F. C. Tank Mount Bracket G. D. Tank Mount Plate H. 3/8” Fender Washers 3/8” Nylon Lock Nuts 5/16” x 1-1/4” Bolts 5/16” SAE Washers © Copyright 2003 Ferris Industries. All Rights Reserved. 1 48714