Unthread HANDLE BASE (1) from DECK ADAPTER (2). Pull HANDLE ASSEMBLY off VALVE STEM (3). Remove SPRING CLIP (4). Lift STOP WASHER (5), turn 90° and replace. Replace SPRING CLIP (4). Find correct position of HANDLE ASSEMBLY by adjusting male teeth on VALVE STEM (3) to female teeth in HANDLE. Thread HANDLE ASSEMBLY onto DECK ADAPTER (2) until snug against mounting surface. 4 3 5 HANDLE ASSEMBLY REMOVE HANDLE 1 2 4 5 3 BOTTOM SPLINE END UP Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
(1816 x 1060 x 559mm) INSTALLED SIZE 71-1/2 x 41-3/4 x 22 In. WEIGHT 115 Lbs. (52 Kg.) (1816 x 1060 x 559mm) WEIGHT w/WATER 690 Lbs. (313 Kg.) WEIGHT 115 Lbs. (52 Kg.) GAL. TO OVERFLOW 69 Gal. (261 L) WHIRLPOOL MIN. OPERATING VOL. 60 Gal. (227 L) WEIGHT w/WATER 690 Lbs. (313 Kg.) BATHING WELL AT SUMP 41 x 21-1/2 In. (1041 x 546mm) BATHING WELL AT SUMP 41 x 21-1/2 In. (1041 x 546mm) BATHING WELL AT RIM 62 x 31-1/2 In. (1574 x 800mm) BATHING WELL AT RIM 62 x 31-1/2 In. (1574 x 800mm) WATER DEPTH T
Tub Installation Instructions 0153/0155 Series Introduction: Thank you for selecting our products...products which have been the benchmarks of fine quality for years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture. Recommended Tools & Materials Observe Local Plumbing and Building Codes Adjustable Wrench Regul
FINISHED WALL 79mm(7-1/8) 13mm (1/2) 23mm (7/8) C/L OF SEAT POST HOLES 140mm (5-1/2) CTR'S. 305mm (12) C/L C/L OF SUPPLY AS REQUIRED FINISHED FLOOR 176mm (7) 736mm (29) 473mm (18-1/2) 140mm(5-1/2)203mm (8) 343mm (13-1/2) 305mm (12) 384mm (15) 767mm (30-1/4) 388mm (15-5/16) 413mm (16-1/4) 355mm (14) 6 7 INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions. 8a 8bBefore continuing, determine the type of water supply connecation you have from the chart below and use t
To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. ACRYLIC SHOWER BASE MODELS: 3232.ST, 3636.ST, 4242.ST, 4832.ST, 4834.ST, 6032.STLH, 6032.STRH, 6034.ST, 3636 NEO, 3838.NEO, 4242.NEO For alcove (.ST models) installation only: The opening dimensions should be 1/8" larger than dimensions shown. © AS America, Inc. 2008 751817-100 Rev. QFOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS. CLEANING AND MAINTENANCE D C E F G H DRAIN ASSEM
In Massachusetts, the maximum output temperature of the shower mixing valve can be no higher than 112.F. Recommended tools (not included) grease pencil or other marking tool level ruler 2 & 3 mm Allen wrenches 6 mm drill bit 8 mm wrench Philips screwdriver waterproof sealant ............................................................ 8 mm 2 mm 3 mm 6 mm Installation Drill the screw holes with a 6 mm bit. Install the anchors. If both ends of the showerpipe are mounted on tile, install the top an
customer's e-mail us at: faucetsupport@amstd.com For Parts, Service, Warranty or other Assistance, please call 1-800-442-1902 (In Canada: 1-800-387-0369) NOTE TO INSTALLER: Please give this manual to the customer after installation. (In Toronto Area only: 1-905-3061093) Specifications Installation Adjust Temperature Service Replacement Parts 1 2 3 3 4 Installation InstructionsInstallation InstructionsSELECTRONIC™ Thermostatic Mixing Valve Certified to comply with ASME A112.18.1M © 2005 American
Escutcheon plate (use is optional). □ 1340M.000X Vandal Resistant Metering Faucet with mixing valve. Built-in strainer and checks. Less escutcheon plate. □ 1340.000 Vandal Resistant Metering Faucet less mixing valve. Single supply for cold or tempered water. Escutcheon plate (use is optional). 48mm (1-7/8) 111mm (4-3/8) 38mm V- (1-1/2) 44mm (1-3/4) MAX 70mm (2-3/4) MIXING VALVE WITH BUILT-IN CHECKS AND STRAINER (ON APPLICABLE MODEL) 38mm (1-1/2) NOTE: Dimensions are shown for p