UltraATA 133 PCI RAID layout Hardware Installation HDD Activity LED General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with internal parts and handle cards only

page 6 Verify Windows 98SE/ME Installation ..............page 6-7 Windows NT 4.0 ....................................................... page 7 Verify Windows NT 4.0 Installation ...................... page 8 Windows 2000 ........................................................... page 8 Windows XP/Server 2003 ....................................... page 9 Verify Windows 2000/XP/2003 Installation ...... page 10 Bios Configuration..................................................page 10 Windows 9

2. At the Found New Hardware Wizard, insert the driver diskette, select Install the software automatically (Recommended), then click Next. 3. Click Finish, remove the driver diskette and restart Windows to complete the installation. To Verify Windows 2000/XP/2003 Installation To Verify Windows 2000/XP/2003 Installation . Right click My Computer and click Manage. 2. Select Device Manager. 3. Double click SCSI and RAID Controllers, then double click Silicon Image SiI 0680 ATA/133 Controller to dis

4. Insert the driver diskette and press Enter. 5. Select Silicon Image SiI 0680 ATA/133 Controller and press Enter. 6. Press Enter to continue and follow on-screen instructions to complete Windows NT 4.0 installation. For Existing Windows NT 4.0 Installation 1. Install the board and boot up Windows NT 4.0. 2. Double click My Computer/Control Panel/SCSI Adapters, then click the Drivers tab. 3. Click Add… then Have Disk.... 4. Insert the driver diskette, type in A:, then click OK. 5. Highlight Sil

Key product features are: • 5V 0.5A power consumption • Supports resolutions to UXGA • Up to 165 MHz pixel rates Installation Figure 1: Location of Input/Output Connections 1. Connect the DVI source device to the splitter marked INPUT on the B116-002. (Figure 2) Figure 2: Connection of DVI Sources 2. Connect the DVI cables between the DVI displays and the B116-002 splitters marked OUTPUT MASTER and OUTPUT SLAVE. Make sure that the DVI source cables are connected to the INPUT port, and that and t

• Features built-in Equalization and Gain controls to adjust the video image • Supports video resolutions up to 1920x1440 • No drivers required Product Features Optional Accessories • P502-Series Monitor Cables with RGB Coax, HD15 Male/Male • N020-01K-GY Cat5e Bulk Stranded Cable, 1000 ft. • N022-01K-GY Cat5e Bulk Solid Cable, 1000 ft. • N222-01K-GY Cat6 Bulk Solid Cable, 1000 ft. Specifications Signal Type VGA, SVGA, XGA, UXGA and WUXGA Video Amplifier Bandwidth 350 Mbps Input DDC Signal 0.7 Vo

• Do not attempt to service this unit. Instead, disconnect it and visit • Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide. Package Contents • Local Unit • Remote Unit • VGA with Audio Splitter Cable • (

35th Street, Chicago, IL 60609 USA Note: Follow these instructions to ensure proper operation and prevent damage to this device and its connected equipment. Copyright © 2009 Tripp Lite. All rights reserved. All trademarks are the property of their respective owners. 2 Safety Information • To reduce the risk of electric shock, do not expose the product to moisture. • Operate this product using only the included external power supply. Use of other power supplies could impair performance, damage th

35th Street, Chicago, IL 60609 USA Package Contents: • B120-000-SL DVI Single Link Active Extender • External Power Supply (Input: 100-240V, 50/60Hz, 0.5A Output: 5V, 2A) • Screwdriver for Equalization Adjustment • Owner’s Manual Product Features: • Supports a maximum video resolution of 1920 x 1080 @ 60Hz • Extend a DVI-D video signal up to 150 ft. from the source • Built-in Equalization control to adjust the video image • HDCP compliant Installation Note: Test to make sure that the entire inst