If model FOAK-4LD is used it must be used in conjunction with locally purchased, non-combustible Class 1 or Class 0 flexible duct. Outside Combustion Air Kits (with duct) 81L87 FOAK-4 (without duct) 81L88 FOAK-4LD Wall Switch Kit 85L87 FWSK Gas Conversion Kits WARNING: THIS CONVERSION KIT SHALL BE INSTALLED BY A QUALIFIED SERVICE AGENCY IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS AND ALL APPLICABLE CODES AND REQUIREMENTS OF THE AUTHORIZED AGENCY HAVING JURISDICTION. IF THE INFORMATION IN

These appliances may be used for bedroom installations in the United States and are listed accordingly. These units may not be installed in bedrooms in Canada. CLEARANCES Minimum clearance to combustibles for the appliance is as follows: sides and back - 0" (0 mm), floor - 0" (0 mm), adjacent wall - 0" (0 mm), ceiling - 64" (1626 mm). NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. APPLIANCE SPECIFICATIONS 4" (146 mm) 5 ..." (102 mm) 7 ..." (184 mm) 33 ..." (851 mm) 6" (152 mm) Front Appliance Top

(In Canada, the current CSA C22-1 Canadian Electrical Code.) 1. If any of the original wire as supplied must be replaced, it must be replaced with Type AWM 105°C – 18 GA. wire. 2. 120V, 60Hz – Less than 3 amps. BK Junction Box Transf. 120 V. 24 V Factory Wired Field Wired BL Electronic Wiring Diagram (Honeywell) (Optional ON/OFF Switch Wiring) R BK BL To Opposite Side G W OPT. ACCESSORY SWITCH 120 VAC. BK LIMIT SWITCH W Gas Valve B OPTIONAL ON/OFF SWITCH OR WALL SWITCH R IGNITER CONTROL PILOT AS

The gas line may however be alternately routed from the left side. When rigid pipe is used, an ANSI approved manual shut-off valve and union must be installed upstream of the fireplace. Ensure that a sediment trap is installed in the existing gas line, if not, install a sediment trap upstream to prevent moisture and contaminants from passing through trap to the appliance controls and burners. Failure to do so could prevent the appliance from operating reliably. An external regulator must be used

116-F-13-4) to ANSI Z21.88-2002 (in Canada, CSA-2.33-2002), and CAN/CGA-2.17-M91 in both USA and Canada, as vented gas fireplace heaters. Both millivolt and electronic versions of these appliances are listed by Omni-Test Laboratories for installation in bedrooms and mobile homes. Installation must conform to local codes. In the absence of local codes, installation must comply with the current National Fuel Gas Code, ANSI Z223.1. (In Canada, the current CAN-1 B149 installation code.) Electrical w

(page 9) Install the vent system and exterior termination. Step 4. (page 21) Field Wiring a. Millivolt Appliances – Install the operating control switch (not factory provided) and bring in electrical service line for forced air circulating blower (optional equipment). b. Electronic Appliances – Field wire and install operating control switch. Step 5. (page 21) Install blower kit (optional equipment). Step 6. (page 22) Make connection to gas supply. Step 7. (page 22) Install the logs, decorative

These fireplaces must be vented directly to the outside. The vent system may not service multiple appliances, and must never be connected to a flue serving a solid fuel burning appliance. The vent pipe is tested to be run inside an enclosing wall (such as a chase). There is no requirement for inspection openings in the enclosing wall at any of the joints in the vent pipe. Preparing the Appliance Vent Collar on D-500/600/800 Series (Combined Top and Rear Vent) Models Each of the unit's two vent c

1 ea. Surround Kit 1 ea. Surround Trim Kit 1 ea. Face Kit 1 ea. Instruction Sheet GENERAL INfORMATION All of these parts may scratch and bend, great care should be used in handling them. If you encounter any problems, need clarification of these instructions or are not qualified to properly install this kit, contact you local distributor or dealer. Read this instruction sheet in its entirety before beginning the installa face / Surround Panel Kits (Required) -Includes Black face, Surround, and B

Please read and understand these instructions before beginning your installation. Do not alter or modify the fireplace or its components under any circumstances. Any modification or alteration of the fireplace system, including but not limited to the fireplace, chimney components and accessories, may void the warranty, listings and approvals of this system and could result in an unsafe and potentially dangerous installation. IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS: INSTALL THIS FIRE

INSULATION OR VAPOR BARRIERS, IF USED, MUST FIRST BE COVERED WITH GYPSUM BOARD, PLYWOOD, PARTICLE BOARD OR OTHER MATERIAL TO ASSURE INSULATION AND VAPOR BARRIERS REMAIN IN PLACE. WARNING: DO NOT PACK OR FILL RE- QUIRED AIR SPACES WITH INSULATION OR OTHER MATERIAL. NO MATERIAL IS ALLOWED IN THESE AREAS. Figure 2 Insulate Joists Same As Ceiling Draft Stops Firestop CTDT Termination Note: Non- Combustible Chase FlashingMust Be Used To Cover Chase Opening OptionalInsulation In Outside Walls Of Chase