Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Superior Dateigröße: 475.12 kb Dateiname: Unterrichtssprache:

The gas line may however be alternately routed from the left side. When rigid pipe is used, an ANSI approved manual shut-off valve and union must be installed upstream of the fireplace. Ensure that a sediment trap is installed in the existing gas line, if not, install a sediment trap upstream to prevent moisture and contaminants from passing through trap to the appliance controls and burners. Failure to do so could prevent the appliance from operating reliably. An external regulator must be used on all propane (L.P.G.) heaters to reduce the supply tank pressure to 13" w.c. (maximum). Any copper tubing used to supply propane (L.P.G.) from the tank must be internally tinned. IMPORTANT: HOLD GAS VALVE SECURELY TO PREVENT MOVEMENT WHEN CONNECTING TO INLET GAS LINE WARNING: CONNECTING DIRECTLY TO AN UNREGULATED PROPANE (L.P.G.) TANK MAY CAUSE AN EXPLOSION. All appliances are equipped with a gas flex line and shutoff valve attached directly to the gas control valve. To quickly and easily complete the gas line routing, use the gas flex line kit. Step 3. Slide the fireplace into prepared framing or position fireplace in its final position and frame later. RIGHT SIDE 5 ..." (146 mm) 2 ..." (57 mm) Figure 8 Refer to fireplace drawings and specifications on pages 4 and 5for framing dimensions and details. Framing header may be positioned directly on the fireplace top spacers. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 10 Note:Refer to the vent manufacturers installation instructions for variations of venting techniques. If common venting of several units is contemplated, it should be discussed with an architect and the local Building Department. CAUTION: THIS APPLIANCE CANNOT BE VENTED HORIZONTALLY. Figure 11 1 - Vertical -Minimum overall height of the vent system and appliance without an offset must be 12' (3.66 m) 2 - With Offset -Minimum overall height of the vent system and appliance must be 15' (4.57 m) when an offset up to 60 degrees from the vertical is used. There must be a minimum vertical vent height of 2 ft. (0.6 m) above the appliance collar before the offset can be applied. 3 - With Offset, when using the optional, 36GEP or 36GEP-BB, non-operable glass doors - Minimum overall height of the vent system and appliance must be 12' (3.66 m) when an offset up to 60 degrees from the vertical is used. The lower part of the offset may start at the appliance flue collar. Maximum overall height of the vent system and appliance should not exceed 40 feet (12.19 m). Install the B-vent system in accordance with the vent manufacturer's instructions. IMPORTANT: UNDER NO CIRCUMSTANCES CAN THE FIREPLACE TOP SPACERS (FIGURE 2) BE REMOVED OR MODIFIED, NOR MAY YOU NOTCH THE HEADER TO FIT AROUND OR BE INSTALLED LOWER THAN THE SPACERS. THE HEADER MAY BE IN DIRECT CONTACT WITH THE TOP SPAC- ERS BUT MAY NOT BE SUPPORTED BY THEM. Fireplace should be secured to side framing members using provided nailing flanges. Use 8d nails (see Figure 9 ). Figure 9 Note: The nailing tabs and the area directly behind the nailing tabs are exempt from the clearances described on the fireplace clearance label. Step 4. Install the Vent System and Exterior Termination - A -Connect a 4" (102 mm) Type B vent system to the appliance flue collar with two (2) No. 8 sheet metal screws (Figure 10 )and install the remainder of the Type B vent to the outside. B -The following venting configurations may be installed (see Figure 11): *This Vent Configuration Allowable Only WithThe Following Optional Non-Operable Glass Doors installed: 36GEP or 36GEP-BB 4” Type BVent Flue Outlet Collar 15 ft. Minimum With AnyOffset 2 ft. Minimum To Offset 12 ft. Minimum 60* degreesMaximum Back View Of Appliance Back View Of Appliance 60 degreesMaximum 12 ft. Minimum Back View Of Appliance 1 2 3 8d Nail Framing Appliance Louver Nailing Flange Step 5. Field Wiring – Refer to Section A for millivolt appliances and Section B for electronic appliances. A. Millivolt Wiring – Units may be fitted at the factory with either a Honeywell millivolt gas control valve or an SIT millivolt gas control valve. Both valves have been tested with and approved for use with these appliances and are listed accordingly. Refer to Figure 12 for wiring of Honeywell systems andFigure 13for wiring of SIT systems. The gas valve has been set in place and has been pre-wired at the factory. No additional wiring is required unless the optional wall switch or optional remote control kit is to be installed. Locate the optional wall switch or optional remote control in the desired location and connect the millivolt wire (see Figures 12 and 13 ). CAUTION: DO NOT CONNECT THE WALL SWITCH TO A 120V POWER SUPPLY. Thermopile TH TP TH TP Honeywell Millivolt Wiring Diagram If any of the original wire as supplied must be replaced, it must be replaced with Type AWM 105°C – 18 GA. wire. TH TPTH TP * For Wall Switch Attachment Only. * Limit Switch BK WHT BK BK Figure 12 SIT Millivolt Wiring Diagram If any of the original...

Herunterladen

Geben Sie zwei Ziffern: