28. Compressed air from the unit may contain carbon monoxide. Air produced is not suitable for breathing purposes. 29. Always use a respirator when spraying paint or chemicals. 30. The air pressure switch is set at the factory for optimum performance of your equipment. Never attempt to bypass or remove this switch as serious damage to equipment or personal injury could result from excessive air pressure. 2 KNOW YOUR COMPRESSOR Handle Air Filter Air Chuck Regulator Pressure Gauges Figure 1. Air C

Before using this product, please read the following instructions carefully. Technical Specifications Item Description Item Description Square Drive 1/2" Air Inlet Diameter 1/4"- 18NPT Free Speed 145 RPM Min. Hose Size 3/8" Max. Torque 65 ft-lbs Max. air pressure 90 PSI Air Consumption 4.5 CFM SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep this manual a

It is important that you read the entire instruction sheet to become familiar with this product before you begin using it. This machine is designed for certain applications only. Northern Tool & Equipment strongly recommends that this machine is not modified and/or used for any application other than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted Northern Tool & Equipment to determine if it ca

Do not use a pneumatic tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating pneumatic tools may result in serious personal injury. · Dress properly. Do not wear loose clothing of jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should be avoided. · Always use the appropriate eye and ear protection and oth

Use common sense. . Always be sure to stand inside the Operator Zone when running your log splitter. IMPORTANT: Before starting the splitting operation, cycle pressure plate of the splitter three to four times back and forth by pushing and releasing switches to help remove any air that may have mixed into the hydraulic fluid during handling, storage, etc. Oil is incompressible; therefore, to ensure the efficiency of the log splitter, it is important that the hydraulic system does not contain air

Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handle must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Disconnect air hose when not in use. 11. Avoid unintentional starting. Be sure the trigger is not depressed when carrying the Air Hammer. 12. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate p

2. Securely tighten the Air Chuck in place with a wrench. Note: DO NOT over tighten Air Chuck. (See Figure 3) Installing the Air Filter The metal Air Filter is installed into the threaded port of the cylinder head. 1. Thread the Air Filter into the Cylinder Head by turning the Air Filter clockwise. 2. Securely tighten the Air Filter in place with a wrench. (See Figure 4) Note: DO NOT over tighten Air Filter. OPERATION BEFORE OPERATING YOUR NEW AIR COMPRESSOR please check the following points car

The plug and outlet should look like those in the following illustration. (See Figure A.) PAGE 7 DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either

Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. PRODUCT SPECIFICATIONS Model HGS220/440LB HGS550/1100LB HGS750/1500LB HGS1000/2000LB Standard version With pulley Hook Standard version With pulley Hook Standard version With pulley Hook Standard version With pulley Hook Load capacity 220lb 440lb 550lb 1100lb 750lb 1500lb 1000lb 2000lb Lifting height 36ft 18ft 36ft 18ft 36ft 18ft 36ft 18ft Lifting speed 33ft/min 16.5ft/min 33ft/min 16.5ft

If you are unable to hoist a load and the load is under the maximum lift capacity, stop the Hoist and allow the motor to cool down before trying again. 18. Make sure the cable is correctly wound around the wheel. See FIGURE 1 below. 19. Do not support a load over or around people or animals. 20. Do not leave load suspended in the air unattended. 21. Do not allow a load to bear against the hook latch. Allowing a load to bear against the hook latch can result in loss of load. 22. Do not allow load