OPERATING CONTROLS Item Description Function 1 Main Power Switch with Built- In Indicator Lights A three way rocker switch with a center off position. Pressing the left side of the rocker switch (COOK position) operates the fryer, and the amber light illuminates. No light is visible when the switch is in the OFF position. To filter, press the right side of the rocker switch (PUMP position) to operate the pump motor, and the red light illuminates. 2 Single Stage Thermostat An electromechanical de

Before troubleshooting, always recheck the operation pro- cedures per Section 3 of this manual. To isolate a malfunction, proceed as follows: 1. Clearly define the problem (or symptom) and when it occurs. 2. Locate the problem in the Troubleshooting table. 3. Review all possible causes. Then, one-at-a-time work through the list of corrections until the problem is solved. 4. Refer to the maintenance procedures in the Maintenance Section to safely and properly make the checkout and repair needed.

To operate the valves, unscrew the two knurled screws and remove the service cover. Open or close manual valves as desired. Gas Leak Test After piping and fittings have been installed, check for gas leaks. A simple checking method is to turn on the gas and brush all connections with a soap solution. The appearance of bubbles indicates escaping gas. In this event, the piping connection must be redone until no bubbles occur. Never use a lighted match or open flame to test for gas leaks. Escaping

INTRODUCTION This section provides procedures for the checkout and replacement of the various parts used within the blast chiller/freezer. Before replacing any parts, refer to the Troubleshooting Section. It will aid you in determining the cause of the malfunction. 2-2. MAINTENANCE HINTS 1. You may want to use a multimeter to check the electric components. 2. When the manual refers to the circuit being closed, the multimeter should read zero unless otherwise noted. 3. When the manual refers to t

Find the appropriate wires to the PC board and remove the wires from the board. 6. Pull the probe wire through the wiring harness. 7. Install new probe in reverse order. 2-11. FRIGIPROBE 1. Remove the electrical power to the unit. Air Probe Evaporator Probe Frigiprobe To avoid electrical shock or property damage, move the power switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 2. Using a Phillips head screwdriver, remove the two screws securing the evaporator

Drum will hold up to 10 pounds of breading. 3. Feed raw moist product into hopper assembly. 4. Product will emerge from the other end of drum. 5. Place product into pan or wire grid for frying process. Do not place hands or objects into drum while machine is operating, or personal injury or damage to unit could result. CLEANING (Refer to Exploded View) 1. Remove hopper (32) and hopper stand (33) from unit. 2. Dissassemble end caps (36), blade assembly (34), and cylinder assembly (34), and

This unit will NOT hold potentially hazardous food at a safe temperature 1. Turn power switch to the ON position. 2. After a sequence of codes the display shows the time of day, or “ON”. KKôJÜM Press and hold the TEMP button to view the actual temperature of the unit. Temperature Setpoint Programming 1. Press and hold the TEMP button for 6 seconds. The actual temperature shows first followed by the flashing setpoint temperature. 2. While holding in on the TEMP button, press and release

This unit will NOT hold potentially hazardous food at a safe temperature 1. Turn power switch to the ON position. 2. After a sequence of codes the display shows the time of day, or “ON”. KKôJÜM Press and hold the TEMP button to view the actual temperature of the unit. Temperature Setpoint Programming 1. Press and hold the TEMP button for 6 seconds. The actual temperature shows first followed by the flashing setpoint temperature. 2. While holding in on the TEMP button, press and release t

Press the TEMP button to turn the relays, display and heaters, OFF and ON. 6. Press the SET button, and “In-” shows in the display. Press and hold either the UP or DOWN button until “In- SYS” shows in the display. This programs factory settings back into the controls. 7. Press the SET button. If “C=y” shows in the display, the time of day shows in the display during normal operation. If “C=n” shows in the display, “ON” shows in the display during normal operation. Press the UP and DOWN buttons

This unit will NOT hold potentially hazardous food at a safe temperature 1. Turn power switch to the ON position. 2. After a sequence of codes the display shows the time of day, or “ON”. KKôJÜM Press and hold the TEMP button to view the actual temperature of the unit. Temperature Setpoint Programming 1. Press and hold the TEMP button for 6 seconds. The actual temperature shows first followed by the flashing setpoint temperature. 2. While holding in on the TEMP button, press and release t