†Includes 6" for five-compartment supply dispense (optional). Due to continuous improvements, design and specifications subject to change without notice. The quality management systems at all Alliance Laundry Systems manufacturing facilities are registered as ISO 9001:2000 compliant. Printed in the U.S.A. Printed on paper manufactured with virgin pulp from certified sources and a minimum of 10% post-consumer recovered fiber. AL07212©Copyright2007AllianceLaundrySystemsLLC TheWasher-ExtractorFeatu

3. Dress garment on buck. 4. Simultaneously push and hold both CLOSE pushbuttons (Items 1 and 6, Figure 2) until head closes and pressing pressure is applied. Release both pushbuttons. NOTE: If either pushbutton is released BEFORE pressing pressure is applied, head will return to a fully OPEN position. 5. Once garment is sufficiently pressed, press OPEN pushbutton (Item 5, Figure 2) to open press. 6. Hang or fold pressed article as soon as possible to preserve finish. Presses With Timers ONLY 1.

These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine. Indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death. DANGER Indicates a hazardous situation that, if not avoided, could cause severe personal injury or death. WARNING Indicates a hazardous situation that, if not avoided, may cause minor or moderate personal injury or property damage. CAUTION Additional precautionary st

7.Check that the collar block is positioned in the head cutout per Figure 6. If collar block is not properly aligned, check press level. If press is level, shim buck, adjust collar block or discharge tube as necessary. 1/8 in. (3 mm) 1/8 in. (3 mm) 1/8 in. (3 mm) CAB240N Figure 6 8.Press the head release button. Heads should open and buck should return to the dressing station. 9.Simultaneously press and release both buck in buttons. As buck travels into cabinet, press red safety bar which is nea

3 2 Technical data and dimensions ....................................................... 4 Technical data ................................................................................ 4 Dimensions ..................................................................................... 5 3 Installation and connection ............................................................. 6 Ground ............................................................................................ 6 Removing the tr

Ventilation soap dispenser B. Liquid soap connetions C. Hard water connections 3/4" D. Warm water connections 3/4" E. Soft water connections 3/4" F. Connections clamps G.Electrical connections H.Emergency button I. Ventilation tub K. Drain valve L. Steam connections Dimensions 2 HF150 - 185 720 35 1265.5 1386 155.5 251 346 94 173 165 105 1309.5 F L K A C B D E G I 1500 738 900 81 81 1527.5 645 HF234 = 939.5 HF234 = 926 HF234 = 830 70 35 60 35 240 H Dimensions 2 HF234 A. Ventilation so

By activating F1 during low spin, this low spin will be extended to15 minutes unless the START button (S) is pressed earlier. If the 15 minutes of low spin have been completed, the high spin isautomatically canceled. By activating F1 after the preprogrammed low spin, you will have a maximum of 14 minutes of high spin unless the START button (S) is pressed earlier. Adjustable stop time : Here you can program a certain stop time. The display shows the countdown of this extra time. When this time i

This correction will have to be preprogrammed and is not activated on program numbers higher than 20. The corrected time will also be lost when the power has been cut from the machine for more than 24 hours. The right display will continue to show the selected program number. If a Level-stop was programmed (which halts the programmer during the fi lling of the cylinder) and/or a Heat-stop (which stops the programmer during the heating up of the wash bath, then the respective LED’s light up in th

The total time of both programs together is not displayed. The right display alternately shows the program in operation (during a longer time span) and the second program to be executed (during the shorter time span). After the fi rst program has been run, only the second program number will be displayed. Cool down This function allows to gradually lower the temperature of the wash bath to prevent creasing of the linen. During a cool down, the remaining program time on the central display will b

Store these products out of the reach of children. p . Always take into account the instructions on the labels of clothes. Never allow children to play in the surroundings of a machine. p p Remark: These instructions surely cannot prevent all risks of accidents. It is up to the user to act with the utmost precaution. Do not hesitate to contact the dealer in case of a problem. 3 Technical data and dimensions Technical data HF 455 HF 575 Capacity (dry weight) 1/11 40,9 kg 51,8 kg 1/10 45 kg 57 kg