Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Cissell Dateigröße: 1.7 mb Dateiname: Unterrichtssprache:

This correction will have to be preprogrammed and is not activated on program numbers higher than 20. The corrected time will also be lost when the power has been cut from the machine for more than 24 hours. The right display will continue to show the selected program number. If a Level-stop was programmed (which halts the programmer during the fi lling of the cylinder) and/or a Heat-stop (which stops the programmer during the heating up of the wash bath, then the respective LED’s light up in the display. Once the required water level and/or temperature have been reached, the LED is turned off and the internal programmer advances again. Wash cycle-LED’s Each program segment has a corresponding LED. Each of these 6 LED’s light up when the appropriate segment is executed. This way, the program sequence can be accurately followed. When a LED blinks, the machine is taking up water. When a LED blinks slowly, the machine is heating up the water. Spin-LED’s When the water is drained at the at the end of a program segment and the machine spins if so desired, the left spin-LED (intermediate spin) will light up together with the cycle-LED. LED drain/distribution low spin coast Interm. spin blinking rapidly continuously continuously - Functioning of the spin-LED’s during gentle-intermediate spin: LED drain/distribution low spin coast Interm. spin blinking rapidly blinking slowly blinking slowly - Functioning of the spin-LED’s during intermediate spin: 15 4 During fi nal spin, both the left spin-LED (intermediate spin) will light up together with the right spin-LED (fi nal spin). - Functioning of the spin-LED’s during fi nal spin: LED drain/distribution low spin high spin coast tumble Interm. spin blinking rapidly continuously slowly continuously off Final spin continuously continuously slowly continuously rapidly - Functioning of the spin-LED’s during gentle-fi nal spin: LED drain/distribution low spin high spin coast tumble Interm. spin blinking rapidly slowly ---- slowly off Final spin continuously continuously ---- continuously rapidly Manual interventions during the program Following functions can be activated during the program: F1 = Time stop To increase the duration of a program segment beyond its originally programmed duration. F2 = Soak To soak heavily soiled linen F3 = Reduced wash action To avoid wear of delicate garments F4 = Execute high spin as low spin To avoid creasing delicate linen F5 = Rapid advance To skip certain program segments F6 = No spin To give total protection to delicate garments F7 = on the left display appears the number of revolutions of the drum. F8 = changing the number of revolutions at fi nal spin. In order to limit the rpm for delicate linen. Selecting a function Push the SELECT-button (P) at the time the special function needs to be activated and keep the button depressed. Now push the START-button (S) simultaneously and release same. Only now release the SELECT-button (P). The central display now shows F1 and this function is now active. By pressing the SELECT-button (P) the next function will appear on the central display. And so on up to F8. To return to normal operation, press the START-button (S) and release. A function is also terminated by selecting another function. Functions are also automatically ended and switched off at the end of the each program. 16 4 Function F1 (Time stop) During the wash cycle: The wash time is stopped. The temperature, water level and wash action remain the same as programmed. During the wash cycle, this function remains active until the START button (S) is pressed again. During intermediate spin : The intermediate spin normally lasts 1 minute. By activating function F1, the machine will spin for nine minutes unless the START button (S) is pressed earlier. During fi nal spin : At fi nal spin, you have high spin after low spin. By activating F1 during low spin, this low spin will be extended to15 minutes unless the START button (S) is pressed earlier. If the 15 minutes of low spin have been completed, the high spin is automatically canceled. By activating F1 after the preprogrammed low spin, you will have a maximum of 14 minutes of high spin unless the START button (S) is pressed earlier. Adjustable stop time : Here you can program a certain stop time. The display shows the countdown of this extra time. When this time is expired, the function will appear automatically and the program will continue. Select F1 (see above). The stop time can be programmed by means of the ECO button (E). By pressing it once, the stop time is programmed for 10 minutes. From now onwards, “F1” and “10” appear by turns on the middle display. By pressing the ECO button (E) once more, you add each time 10 minutes. After 50 minutes, 1.0, 1.1, 1.2, etc... appear with a maximum of 4.0 hours. By means of the START button (S), you can each time reduce 10 minutes. Description of the functions Remark : The programmed stop time is executed after the decimal point in the right displ...

Herunterladen

Geben Sie zwei Ziffern: