WORKING CIRCUMSTANCE 1. To reduce the risk of injury associated with exhaust fume inhalat i o n , d o n o t o p e r a t e i n unventilated area. The exhaust gases contain harmful carbon monoxide. 2. Avoid using the blower where stable footing and balance are not assured. 3. Never operate the machine in high wind, bad weather, potentially explosive atmosphere, when visibility is poor or in very high or low temperatures. (Our recommended use environment is below 40 degrees C (104 degrees F).) AVOI

(OP2) 7. Allow the engine to warm up for a several minutes before starting operation. 1. When restarting the engine immediately after stopping it, leave the choke open. 2. Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it. NOTE IMPORTANT WARNING 8. Operation OP1 (1) (2) (3) OP2 (4) (7) (5) (6) OP3 OP4 NOTE IMPORTANT WARNING 8. Operation OP1 (1) (

2. KOMATSU ZENOAH does not warrant the machines, those which have been damaged by the use of any parts other than those specified by the company. 3. When placing orders of parts for repair and/or replacement, check if the model name and the serial number are suitable to those specified in the parts list, then use parts number described in the parts list. 4. The contents described in the parts list may change due to improvement. 5. The parts for the machine shall be supplied within ten (10) years

This unique mechanism brings you many benefits like the following: 1. Since the blade does not cause grass chips and pebbles to the thrown around, you may use less care about your clothing or surroundings. 2. Should the blade hit a rigid object like stones, trees or steel poles during operation, it does not produce a bounce motion that can cause loss of machine control. 3. Since the blade does not cause cut grass to wrap around the neck, you need not to stop operation to remove such wrappers. Wh

Pay attention to agitation. 1. Measure out the quantities of gasoline and oil to be mixed. 2. Put some of the gasoline into a clean, approved fuel container. GB-9 SGCZ2600DL/SGCZ2600DW 8. Operation STARTING ENGINE WARNING The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 2. Push the primer pump several times until overflow

Check and clean the filter element in warm, soapy water as required. Dry completely before installing. If the element is broken or shrunk, replace with a new one. IMPORTANT • Note that using any spark plug other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and G damaged. B •To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench. 87 ~ 104 in-lbs TIGHTENING

T3074-12110 1 2 3 4 5 6 7 8 9 10 SHAFT GRIP LEVER COMP. • CORD (A) • CORD (B) • TUBE • CABLE PLATE-NAME PLATE 3074-12210 3577-32141 T3002-12200 T3002-12220 T3002-12230 T3002-12240 T3002-83100 RMS9-99001 6425-12552 1 1 1 1 1 1 1 1 1 Key# Description Part Number Q'ty 11 TOOL-SET T3002-91000 1 12 13 14 15 • SOCKET • WRENCH • SPANNER • BAR T3002-91310 09007-00425 3540-91120 3540-91110 1 1 1 1 Fig.5 SWEEPER GROUP (S/N 000000 and up) Key# Description Part Number Q'ty 1 Gear Case 99909-33031 1 2• Bolt

Including Safety Kit (Fig.2 Key#32) 99909-11001 1 12 • Nylon Brush Ass’y Contents a pair of burush 99909-11004 1 Key# Description Part Number Q'ty 13 • Gear Shaft Adapter, LH 99909-11112 1 14 • Gear Shaft Adapter, RH 99909-11113 1 15 • End Cap 99909-11114 2 16 • Hardware Kit Roll Pinx2, Flat Washerx2 Bolt RH (Black)x1 and Bolt LH (Silver)x1 99909-311 1 17 Strap Assy T3002-17200 1 18 Hanger Assy 6420-17300 1 19 • Hanger comp. 6420-17400 1 20 • • Hanger 9366-17110 1 21 • • Clamp 9366-17120 1 22 •