• If after several tries, the pilot will not stay lit, turn the gas control knob to "OFF" and call your service technician or gas supplier. 11. Replace glass door. 12. Turn gas control knob to “ON” position. 13. For RN/RP appliances turn the On/Off switch to “ON” position or set thermostat to desired setting. 14. Turn on all electrical power to the fireplace. Euro SIT SIT NOVA Honeywell PILOTON OFF ON PILOT OFF OFF 3 4 5 1 2OFF Pilot 3/8" - 1/2" To Turn Off Gas To Heater 3. Open control access p

Provide for Adequate Ventilation Any space within a home can be classified in these categories: 1) Unusually tight construction 2) Confined space 3) Unconfined space First, determine which classification defines the intended installation space. Unusually Tight Construction You must provide additional fresh air if the space falls into this classification. Unusually Tight Constructionis defined as construction wherein: a. Walls and ceilings exposed to the outside atmosphere have a continuous water

Shut off gas to the appliance. 2. Extinguish any open flames. 3. Open door. 4. If odor continues, keep away from the appliance and immediately call your fire department. Failure to follow these instructions could result in fire, explosion or burn hazard, which could cause property damage, personal injury or death. DANGER 1. Never operate this appliance unattended. 2. Never operate this appliance within 10 feet (3.05m) of any other gas cylinder. 3. Never operate this appliance within 10 feet (3.0

Main Burner shuts off and Pilot 1. Insufficient fresh air. flame goes out while in operation. 2. Incorrect inlet supply pressure. 1. Determine that adequate ventilation exists to provide sufficient fresh air. Open a window or provide additional ventilation. (See Fresh Air Requirements, Pages 7-8) 2. Call local gas supplier. Adjust inlet supply pressure to specification: NG; 5.5” w.c.-14.0”w.c. LP; 11.0” w.c.-14.0”w.c. 20004555 19 Radiance Vent-Free Gas Heater Maintenance The following procedures

SOUPAPES A GAZ : Les soupapes a gaz sont couvertes pour une periode d’un an. COMPOSANTS ELECTRONIQUES ET MECANIQUES : Les composants electroniques et mecaniques du bruleur sont couverts pendant un an. Tous les bruleurs en acier sont garantis pendant un an. ACCESSOIRES : A moins d’indication contraire, tous les composants et accessoires fournis par CFM Corporation sont couverts pendant une periode d’un an. CONDITIONS ET LIMITATIONS • Ce nouveau produit Vermont Castings ou Majestic doit etre insta

Installation Refer to Page 13 for installation instructions. Remote Controls The remote control allows you to turn the heater on or off from anywhere in the room. Refer to Page 40 for wiring diagrams. Model Functions Controlled MRC1 ON/OFF MRC2 ON/OFF and Temperature MRC3 ON/OFF and Temperature control with a digital display and a programmable 24 hour clock IMT Wall mounted thermostat control An optional screen, S30SK, for use with the operable doors is available for the Stardance only. The scre

3. Turn burner upside down and remove air shutter. Discard air shutter. (Fig. 18) Air Shutter (Remove and Discard) Bottom of Burner Pan ST667 Fig. 18 Remove air shutter and discard. 4. Replace burner. Slide the burner in at an angle with left side lower than the right side. Slide the left side onto the injectors, making sure the burner leg remains at a 90° angle to the base. (Fig. 19) Lower the right hand side down in to place. Make sure the burner is as far left as possible and the injector sho

For assistance or additional information consult a qualified installer, service agency, or the gas supplier. Installation and service must be performed by a qualified installer, service agency or the gas supplier. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. This is an unvented gas-fired heater. It uses air (Oxygen) from the room which it is installed. Provisions for adequate combustion and ventilation air must be provided. Ra

Check burner orifices for debris, and remove. Turn knob to ON, place rocker switch to ON, millivolt me- ter should read greater than 10 mV. If the reading is okay and the burner does not light, replace the valve. Clean and/or adjust pilot flame for maximum flame im- pingement on thermocouple and thermopile. Check the vent terminal for blockage. Radiance Direct Vent/Natural Vent Gas Heater Instructions for RF Comfort Control Valve The Comfort Control valve allows remote control of temperature, fa

33 Roof support and flashing. Venting System Assembly - Natural Vent General Information The Radiance Heater is shipped from the factory as a Direct Vent Heater. It may be converted to a Natural Vent heater by installing the Vermont Castings Model Z31D00 FSDHAG Draft Hood Adapter. The Radiance Heater is approved for installation as a Natural Vent unit. Vermont Castings/Majestic Direct Vent outer pipe (7FSSK) could be used directly after the Draft Hood Adapter up to the ceiling, then B-vent pipe