Always wear eye and hearing protection when operating this unit. X7502831700 CAUTION! A statement preceded by the word “CAUTION” contains information that should be acted upon to prevent mechanical damage. Introduction IMPORTANT! The operational procedures described in this manual are intended to help you get the most from this unit as well as to protect you and others from harm. These procedures are guidelines for safe operation under most conditions, and are not intended to replace any safety

Always wear eye and hearing protection when operating this unit. X7502831600 CAUTION! A statement preceded by the word “CAUTION” contains information that should be acted upon to prevent mechanical damage. Introduction IMPORTANT! The operational procedures described in this manual are intended to help you get the most from this unit as well as to protect you and others from harm. These procedures are guidelines for safe operation under most conditions, and are not intended to replace any safety

Blade Installation 4-6 mm (3/16”-1/4”) Throttle Free Play Throttle trigger free play Cable Adjuster AB C 3. Turn the cable adjuster in or out as required to obtain proper free play 4 - 6 mm (3/16 - 1/4 in.). 4. Connect 2 ignition stop leads from throttle cable tubing to 2 ignition leads on engine. 5. Reinstall the air cleaner cover. Remove air cleaner cover WARNING You must install the U-Handle and all Blade Conversion parts shown in the following instructions before operating this unit with a m

MANUFACTURER'S WARRANTY COVERAGE: The emission control system is warranted for 2 years or the length of the ECHO Inc. warranty, whichever is longer. If any emission-related part on your equipment is defective, the part will be repaired or replaced by ECHO Inc. or its Authorized Service Representative. OWNER'S WARRANTY RESPONSIBILITIES: As the equipment/SORE owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. ECHO Inc. recommends that you r

Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components. Fuel Requirements Gasoline -Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. 2 Stroke Mixture Oil - A 2-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345/FD standards mus

25, 27, 29, 31, 61, 81, 89 802-005C ...................25, 39, 61 802-010C ...................19, 89 802-017C ...................43 100 4210ST & 4410ST Utility Vehicles Treker 700-109P 02/19/09 Table of Contents Part Number Index Part Number Index (continued) Part Number Page Part Number Page 802-024C ...................41 802-078C ...................85 802-079C ...................19 802-080C ...................73, 75 802-113C ...................41 802-115C ...................43, 77 802-138C ...

11. 12. 13. 103125 200300 2003PR 2003VB BOLT 5/16-18 X 1.25 SHCS PLUG 1/4-18NPT SCHD PLUG VENT 5PSIV/N005677 BUSHING 1/4NPT X 1/8 NPT * * IMPORTANT NOTES: 1. Use S.A.E 80/90 wt. GL-5 lube. 2. Oil capacity = 6 oz. 07/25/07 4220ST & 4420ST Utility Vehicles Treker 700-504P 57 Table of Contents Part Number Index Land Pride Section 7: Air Filtration TREKER 20 SERIES Air Cleaner Applies to 4220ST, 4420ST 58 4220ST & 4420ST Utility Vehicles Treker 700-504P 07/25/07 Section 7: Air Filtration Table of Co

Table of Contents Part Number Index Table of Contents Section 1: Introduction.................................................4 Using This Manual...............................................................4 Manual Replacement Information.......................................4 Manual Revisions................................................................4 Touch-up Paint....................................................................4 Hardware Legend......................................

Your life and the lives of others depend on it! IMPORTANT: Before you begin, read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information. Your Snow Plow is exclusively designed for your Land Pride NT & ST Treker. Please read these installation instructions and your NT & ST Treker Operator’s Manual thoroughly before beginning. Especially read information relating to safety con

nclosed in oil bath Angle Adjustment Hydraulically controlled 18 degrees right and 22 degrees left Angle Cylinder 2” X 8” Depth Control 2 Each 16.5” x 6.5” Air Tires W/ sealant and 3/4” Roller bearings and Spacer height adjustment Skid Shoes Replaceable Chain Case Lubrication 2 1/2 pints of 80-90 weight Gear Lube - Add gear lube until it escapes from lower plug hole. Designs, specifications, features and information are subject to change without notice. 60 321-004S continue on next