Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Your life and the lives of others depend on it! IMPORTANT: Before you begin, read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information. Your Snow Plow is exclusively designed for your Land Pride NT & ST Treker. Please read these installation instructions and your NT & ST Treker Operator’s Manual thoroughly before beginning. Especially read information relating to safety concerns. Also included in the Operator’s Manual is important information on operation, adjustment, troubleshooting, and maintenance for this attachment (some manual sections do not apply to all accessories). General Information These assembly instructions apply to the following Snow Plow Accessories listed below: 701-067A NT 60" SNOW PLOW 701-068A ST 60" SNOW PLOW Further Assistance Your dealer wants you to be satisfied with your new Snow Plow. If for any reason you do not understand any part of this manual or are not satisfied with the service received, the following actions are suggested: 1. Discuss the matter with your dealership service manager making sure he is aware of any problems you may have and that he has had the opportunity to assist you. 2. If you are still not satisfied, seek out the owner or general manager of the dealership, explain the problem and request assistance. 3. For further assistance write to: Land Pride Service Department 1525 East North Street P.O. Box 5060 Salina, Ks. 67402-5060 E-mail address lpservicedept@landpride.com ! DANGER Exercise EXTREME CAUTION when plowing. Always plow at a slow speed. ! WARNING TO AVOID SERIOUS INJURY OR DEATH: 1. DO NOT EXCEED 5 MPH WITH BLADE INSTALLED. 2. OPERATE WITH EXTREME CAUTION ON SLOPES, STEEP GRADES, AND ROUGH TERRAIN. 3. KEEP AWAY FROM BLADE AND MOVING PARTS DURING OPERATION. 4. WHEN PLOWING SNOW OR DIRT INTO A PILE, START BACKING UP BEFORE RAISING THE BLADE. 5. DO NOT RAM THE BLADE INTO THE PILE. ** SLOW DOWN BEFORE HITTING PILE. ** 6. BE AWARE OF POSSIBLE HIDDEN OBJECTS UNDER SNOW. ! CAUTION TO AVOID PERSONAL OR OTHER INJURY: 1. READ BLADE OWNER?S MANUAL, ATV OPERATOR?S MANUAL, AND SAFETY DECALS BEFORE OPERATING. 2. WEAR HEAD PROTECTION, SAFETY GLASSES, AND SHOES AS RECOMMENDED IN ATV OPERATOR?S MANUAL. 3. ALLOW NO RIDERS ON BLADE OR ATV WHILE MOVING OR STATIONARY. 4. KEEP BYSTANDERS AWAY FROM BLADE OR ATV WHILE MOVING OR STATIONARY. 5. BEFORE ADJUSTING BLADE ANGLE STOP ATV ENGINE, SET AND LOCK BRAKES, RAISE AND LOCK BLADE IN UP POSITION. DO NOT ATTEMPT TO RAISE BLADE BY HAND; USE THE LIFT HANDLE ONLY. 6. BEFORE ADJUSTING BLADE HEIGHT: LOWER BLADE TO THE DOWN POSITION. 7. WHEN BLADE IS NOT IN USE, STOP ATV ENGINE, SET AND LOCK BRAKES, AND LOWER BLADE TO DOWN POSITION. ! ! ! OPERATION ! ! ! Your blade and hardware were designed with your safety in mind. In order to protect you and your machine, certain parts of the blade and / or hardware are designed to fail when the equipment is over stressed. For this reason Push Tubes, Blade Hinges, Foot Peg Brackets, Push Plate Attaching Pins and Clevis Pins are not covered by Warranty. Blade angle is adjustable. Lock blade in the up position. To move the blade left, right or straight, pull the Blade © Copyright 2007 Printed 06/26/07 Land Pride Assembly Instructions Position Lever ahead and turn the blade to the desired position. The Lever will spring back when the blade is at the correct angle. The blade skids are adjustable so the blade can be lowered but still held a certain distance off the ground. The blade is designed to trip when it strikes an object or digs in too far. When pressure is released the blade springs back into position. Blade spring tension may be set stiffer by tightening the Locknuts on the bottom of the Eyebolts. For less spring tension, loosen the Locknuts. Do not exceed 5 MPH with blade installed. Operate with extreme caution on slopes, steep grades and rough terrain. Keep away from blade and moving parts during operation. When plowing snow or dirt into a pile, start backing up before raising the blade. Do not ram the blade into the pile ** SLOW DOWN BEFORE HITTING THE PILE. ** Be aware of possible hidden objects under snow. Wear head protection, safety glasses and shoes as recommended in the machine’s Operator’s Manual. Allow no riders on blade or machine while moving or stationary. Keep bystanders away from blade and machine while moving or stationary. When blade is not in use, stop the machine?s engine, set and lock brakes, and lower blade to down position. Only mature adults over the age of 16 should operate the machinery. Do not operate this machinery if you are under the age of 16. Please read and follow all of the instructions in the owner?s manual. Please read and follow all of the instructions in the machine’s operations manual. Keep all bystanders a minimum of 15 Meters away from the machine and Blade when it is in operation. Do not use this equipment at night (in the dark) or...