When ordering parts, first obtain the Model Number from the name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate illustration and list. Be sure to give all this information . . . Applaince Model Number Part Description Appliance Serial Number Part Number Type of Gas (Propane or Natural) Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardw

12. No gas to pilot. a. LP-regulator shut down due to inlet pressure too high Verify LP tank regulator is installed and set at 11" to 13" w.c. Replace regulator on heater. If the gas quality is bad, your pilot may not stay lit, the burners may produce soot and the heater may backfire when lit. If the gas quality orpressure is low, contact your local gas supplier immediately. HOW TO ORDER REPAIR PARTS Parts can be ordered only through your service person or dealer. For best results, the service p

Metal shipping plate covering burner marked REMOVE must be removed from top of burner and discarded. Burner will not operate if plate is left in place. Make sure you have received all parts: Check your packing list to verify that all listed parts have been received. You should have the following: • Gas log grate/burner assembly. • VFY(M,R)-16SO; 16" logs, three (3) ceramic fiber logs. • VFY(M,R)-(18, 24, 30)SO; 18", 24" and 30" logs, four (4) ceramic fiber logs. • VFY(M,R)-16RWO; 16" logs, four

** Chart shows minimum opening (sq. in.) for given height and input rate. FOR MASONRY BUILT FIREPLACES FREE OPENING AREA OF CHIMNEY DAMPER FOR VENTING COMBUSTION PRODUCTS FROM DECORATIVE APPPLIANCES FOR INSTALLATION IN SOLID FUEL BURNING FIREPLACES Appliance Input Rate (BTU/hr) 20 30 40 Chimney Height* (ft) Minimum Opening** (sq. in.) 6 17.6 25.7 33.8 8 16.5 23.7 31.2 10 15.1 21.7 28.7 15 14.1 19.9 26.1 20 12.9 18.5 23.7 30 12.2 16.9 21.6 * Height is from hearth to top of chimney and the minimum

Check System Operation Millivolt system and all individual components may be checked with a millivolt meter 0-1000 MV range. Remote Receiver -VFYR-(16, 18, 24, 30) Use the following steps to place the remote receiver adjacent to the gas valve. Attention: 1. The remote receiver can not be placed behind the gas valve and burner assembly. 2. When facing the appliance, the remote receiver must be placed to the right of the gas valve and burner assembly. Note: Do not let remote control receiver come

21 Logs Parts List & Parts View ....................................................................................................................... 22 Service Notes................................................................................................................................................ 23 Installer: Please leave these instructions with the consumer. Consumer: Please retain these instructions for future use. 12409-2-0403 Page 2 IMPORTANT SAFETY INFORMATION IMPORTANT SAFE

If you smell gas STOP! Follow “B” in the safety information label. If you do not smell gas, go to the next step. 6. From OFF position, turn the gas control knob counterclockwise to “Pilot” position. Push in and hold control knob for 5 seconds. 7. With the control knob pushed in, push in and release the piezo ignitor button to light the pilot. 8. Continue pushing the control knob in for a further 60 sec- onds to prevent the flame detector from shutting off the gas while the probe is warming up. R

EFFECTIVE DATE APRIL, 2003 This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to page 7. WARNING: If not installed, operated and main- tained in accordance with the manufacturer's instructions, this product could expose you to substances in fuel or from fuel combustion which can cause death or serious illness. WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS Water vapo

This appliance is for installation only in a solid fuel burning fireplace (masonry fireplace or manufactured fireplace) with a working flue and constructed of noncombustible material. Damper stop installation: A damper stop must be provided with the unit. Contact your dealer to obtain one. The damper stop must be installed as shown in (Figure 9) to prevent full closure of the fireplace damper blade and provide a minimum 29 square inch flue opening. State of Massachusetts requirement for installa

11 West 42nd St. Batterymarch Park New York, NY 10018 Quincy, MA 02269 12409-2-0403 Page 7 CLEARANCES CLEARANCES Minimum Dimensions For Solid Fuel Burning Fireplaces UL127 Factory Built Fireplaces (Figure 2) Model ABCD VFYM-16 18" 13" 24" 18" VFYR-16 18" 13" 24" 18" VFYM-18 17" 14" 28" 17" VFYR-18 17" 14" 28" 17" VFYM-24 23" 14" 30" 18" VFYR-24 23" 14" 30" 18" VFYM-30 26" 14" 34" 20" VFYR-30 26" 14" 34" 20" Figure 2 The dimensions shown and defined in the fireplace manufacturer’s instructions ar