To remove the plastic trash bags when full: a. Disengage blades, shift into neutral, engage the parking brake and stop the engine. b. Unlatch and raise cover. c. Remove one container at a time by grasping container handles and pulling toward the rear, off of the tube rails. d. With the container resting on the ground, close and secure the top of the plastic lawn bag. e. Tip the container on its side and slide the filled bag from the container. f. Install a new plastic lawn bag with the edges of

Hinweis: Der Motormaher kann im Accu-Betrieb oder als Handrasenmaher ohne Accu-Antrieb angewendet werden. Vorsicht! Die umlaufende Messerwalze kann zu Verletzungen fuhren. Der durch die Fuhrungsholme gegebene Sicherheitsabstand zwischen Messerwalze und Benutzer ist stets einzuhalten. Beim Arbeiten an Hangen immer quer zum Hang arbeiten und auf sicheren und festen Stand achten. Uben Sie besondere Vorsicht beim Ruckwartsgehen und D A A Die vom Hersteller am Gerat installierten Sicherheitseinrichtu

Introduction This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine. Important Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a resu

A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLE KS 673370945 316251 2000 FAX 316 251 4117 TECHNICAL DATA ZTR Model 3302 IMPORTANT- READ OPERATOR'S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS SEAT ADJUSTMENT 1. Pull or lift body retention latch P/N 3954 from transaxle backing plate, raise and push body and seat assembly forward. 2. Loosen four seat bolts, P/N 3227 and slide seat forward or backward to desired position. 3. Re-tighten seat adjustment bolts P/N 3227. DO NOT

v Always wear an eye shield or safety goggles! v Wear sturdy shoes and long trousers to protect your legs. Keep your fingers and feet away from the cutting filament – above all when starting work. v Always ensure that you have a secure foothold whilst working. v Keep the extension cable away from the area you are cutting. Take extra care when walking backwards. You may stumble ! v Only work in the daylight or when visibility is good. Interrupting work Never leave the Turbotrimmer unattended wher

13 5. Operation 39651240873965124087 2. Insert the two locking bolts 1 from outside through the holes in the two central sections 2 of the upright and secure to the lower sections of the upright 5 with two wing nuts 4. 3. Screw the upper part of the upright with starting handle 3 to the central sections of the upright 2 with two more locking bolts 1 and the wing nuts 4. Thiscompletestheassemblyofthehanle. Warning: Fit the upper section of the upright with starting handle 3 in such a way that the

If the mower must be loaded onto a trailer while there is still debris in the container, the mower must be backed up onto the trailer to avoid tipping. Cleaning and Washing Regular cleaning, washing, and lubricating will prolong the service of the machine. NOTE: Use care with power washers to avoid damage to decals. Limit direct spray on these items. DO NOT EXCEED 1000 PSI WATER PRESSURE FOR CLEANING. For best results, clean polymesh inside hood regularly. Instructions for doing this can be foun

Replace all worn or damaged decals. SAFETY INFORMATION 7 STRAP LANYARD SUPPORT BRACKET ASSEMBLY Collection System Tools Required Ratchet Torque Wrench ." Wrench ." Socket 9/16" Wrench 9/16" Socket 5/8" Socket 1. Open the mounting kit box and remove all of the components. 2. Place the support bracket on the frame and secure with (2) 539 990563, 3/8 x 1 bolts and (2) 539 976979, 3/8 nyloc nuts. 3. Place the hitch brackets on the frame and secure with (3) 990622, . x 1. bolts and (3) 539 101331, .

Grout completely under all frame members. 13. Position washers and nuts on bolts and finger tighten nuts to machine base. 14. Before grout sets completely, make a drain opening in the grouting at the rear center of the machine with a stiff piece of wire. This opening should be approximately .5 inch (13 mm) wide to allow any surface water build-up under the base of the machine to drain away. Do not omit this step. 15. Allow machine grout to set, but not cure. 16. Remove the spacers carefully, all

DO NOT operate mower without seat retention bolts properly tightened. 4. Close upper body and push retention latch (P/N 3934) over transaxle backing plate. BODY REMOVAL 1. The 304 has a (2) piece polyethelene body. The upper body can be folded forward to expose the transaxle. In some cases, it may be necessary to remove the upper body to service the transaxle. 2. To remove upper body, remove two bolts (P/N 3080) from the front of upper body hinge located on the brake shaft (P/N 9283). Disc