Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Dixon Dateigröße: 809.13 kb Dateiname: F8208301en.pdf Unterrichtssprache:

Grout completely under all frame members. 13. Position washers and nuts on bolts and finger tighten nuts to machine base. 14. Before grout sets completely, make a drain opening in the grouting at the rear center of the machine with a stiff piece of wire. This opening should be approximately .5 inch (13 mm) wide to allow any surface water build-up under the base of the machine to drain away. Do not omit this step. 15. Allow machine grout to set, but not cure. 16. Remove the spacers carefully, allowing the machine to settle into the grout. 17. Tighten the nuts by even increments – one after the other using the specified torque – until all are tightened evenly and the machine is fastened securely to the floor. Refer to Table 4. Figure 10 CHM2285N B C A Anchor Specifications(refer to Figure 10) Torque(ft.-lbs.) Models A B (minimum) C 20-60 5/8 in. 2.75 in. (69.9 mm) .625 in. (15.9 mm) 90 (ft.-lbs.) 80-125 3/4 in. 3.25 in. (82.6 mm) .75 in. (19 mm) 175 (ft.-lbs.) Table 4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Installation The completed expansion bolt installation is shown in Figure 11. NOTE: Check and retighten the nuts after five to ten days of operation and every three months thereafter. Figure 12 CHM2284N 1 Washer 2 Locknut 3 Machine Base or Base Frame 4 Machinery Grout 5 Adhesive 6 Expansion Bolt Refer to Table 4 1 5 32 4 6 1.5 in. (38.1 mm) H035I Figure 11 Installing With Elevated Base Frame Elevated Base Frame Installation 1. Verify the floor meets the requirements given in Factory-built elevated steel base frames are designed the Machine Foundation section. to meet the specifications of the 20-60 2 speed, 2. Use the elevated base frame as a template by F-speed and V-speed model washer-extractors only. positioning the frame in the desired location and Refer to Figure 12. The spacing between two marking the pre-drilled mounting holes on the machines provided by an elevated base is .38 inch floor. (9.5 mm) in 20, 30 and 60 pound models and .25 inch (6.3 mm) in 40 pound models. F8208301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 3. Refer to Figure 10 and Table 4 to set the drill depth gauge. 4. Drill the holes to the set depth. Refer to Table 4. 5. Use compressed air or a squeeze bulb to remove debris from each hole. 6. Fill half the hole depth with an industry accepted adhesive anchoring system. 7. Insert bolt until it reaches the bottom of the hole and 1.5 inches (38 mm) of the bolt extends above the base frame. Refer to Figure 11. 8. Allow adhesive around the bolt to cure properly. 9. Position base frame over anchoring bolts. 10. Raise and level the base frame .5 inch (13 mm) off the floor on three points, using spacers such as nut fasteners. 11. Fill the space between the base frame and the floor with a good quality non-shrinking machinery grout to ensure a stable installation. Grout completely under all frame members. 12. Position washers and locknuts on bolts and finger tighten nuts to base frame. 13. Before grout sets completely, make a drain opening in the grouting at the rear of the base frame with a stiff piece of wire. This opening should be approximately .5 inch (13 mm) wide to allow any surface water build-up under the base of the machine to drain away. This drain opening must not be near frame mounting bolts. Do not omit this step. 14. Allow machine grout to set, but not cure. 15. Remove the spacers carefully, allowing the base frame to settle into the wet grout. 16. Tighten nuts by even increments – one after the other using the specified torque – until all are tightened evenly and the base frame is fastened securely to the floor. Refer to Table 4. 17. Position the machine over the base frame, aligning the mounting holes on the machine with the corresponding holes on the frame. 18. Install a bolt, lockwasher, and nut in each mounting hole. Use 5/8 inch – 18 x 2.00 grade 5 mounting bolts with 5/8 inch – 18 grade B nuts and 5/8 inch lockwashers. 19. Hand tighten each nut. 20. Tighten the two rear nuts two turns. 21. Tighten the two front nuts two turns. 22. On 30, 40 and 60 models, tighten the two middle nuts firmly. 23. Tighten the two front nuts firmly; tighten the two rear nuts firmly. NOTE: Check and retighten the locknuts after five to ten days of operation and every three months thereafter. NOTE: For 80 and 125 pound models, a bolt-locator fixture or rebar frame is available as an option. This is designed to be embedded in concrete. Refer to Figure 13. IMPORTANT: Do not install any 80 or 125 machines on an elevated base frame. Figure 13 P035I 1 Machine Base 2 Mounting Bolt Threads 3 Grouting 4 Bolt-Locator Fixture or Rebar Frame 1 2 3 4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F8208301 Installation Mounting Bolt Hole Locations (Without Elevated Base Frames) CHM2224N 26 in. (660 mm) 20 Models 20.66 in. (525 mm) 23.94 in. (608 mm)25- 44 in. (646 mm) 20.88 in. (530 mm) 0.75 in. (19 mm) 2.56 i...

Herunterladen

Geben Sie zwei Ziffern: