The page password range is 1-5,999. • CLEAR Clears the number in the keypad display. • ENTER Sets the page password number, closes the keypad, and returns to the Protected Setup page. Calibrate Press CALIBRATE to open the CALIBRATE decision button shown in Figure 103 and reset the vertical and horizontal touch points on the LCD. • YES Starts the calibration process. Carefully press each crosshair that appears using your finger or dull pointer. When the calibration process is complete, press

The IRX-DM+ (FG458-10/11) is in a UniMount enclosure that fits into most US-style single-gang enclosures. The IRX-DM+ works with AMX 38 kHz or 455 kHz IR transmitters. Note: The IRX-SM+ swivel-mount version is also available for wall or ceiling installations. IR Sensor IR Data LED FIG. 1 IRX-DM+ unimount IR sensor IRX-DM+ Specifications Dimensions (HWD): 4.68" x 2.93" x 1.14" (118.70 mm x 74.40 mm x 29.00 mm) 0.30" (7.70 mm) depth from wall surface Available Colors: White (FG458-10) and Black (F

1. Cut out the surface for the WDS using the dimensions shown in installation diagram SP-5965-01 (reproduced in FIG. 11 on page 10). It is recommended that you cutout the surface slightly smaller than what is outlined in the installation drawings so that you can make any necessary cutout adjustments. Be sure to cut out the four notches along the sides to accommodate the four drywall expansion clips (included). When installing the four #6-32 Mounting Screws in Step 3, turn the screwdriver gently

This is the only method of programming the TPI/3 using Serial Commands. • AXlink connection: Connect a DB-9 cable from your PCCOM port to the Programming port on the Controller. Then use an AXlink cable to connect the AXlink connector on the Controller to the AXlink connector at the rear of the AXB-TPI/3. This is the only method of programming the interface unit using Send_Commands. Included Accessories • Two rack-mount ears and a package of rack screws • One 4-pin AXlink connector • One 2-pin P

It's massive appeal includes quality graphics capabilities, a high-resolution touch screen,a stylish panel design, and low-cost practicality. CONTROL OPTIONS In addition to providing infrared (IR) support, the ViewPoint is available in 1-way and 2-way radio frequency (RF) models. The 1-way ViewPoint is an economical solution for basic control requirements. The 2-way ViewPoint delivers information back to the user as to the current status of the AMX Control System, as well as the ability to use i

For detailed information on the cards, refer to the NetLinx CardFrame, Control Cards, and NetModules Instruction Manual found on-line at NXC-VOL4 Volume Control Card The NXC-VOL4 Volume Control Card provides four discrete volume control channels with LED feedback. The volume control channels can be programmed for mono or stereo operation, and balanced or unbalanced audio connections. It supports programmable audio levels, audio mute, variable ramp speeds and preset levels. Use the on-board jumpe

19 Two-stage furnace and two-stage AC configuration IMPORTANT! The B terminal is for reversing valve-heat. DO NOT connect the B terminal to the common side of the transformer. ViewStat Communicating Thermostat 27J ViewStat Installation and Wiring NOTE Roof top unit (two-stage heat and two-stage cool) configuration. ROOF TOP UNIT 120 ;i VAC ie: гЩ i I VAC ....... FAN RELAY Black (common) (from MiniVerter) 24V FIELD WIRING FACTORY WIRING OPTIONAL 24V FIELD WIRING (SEE NOTE)

5 Sense out connector................................................................................................................ 5 12 VDC power supply connector.............................................................................................. 6 Rack-Mounting the VSS2 (optional)..................................................................................7 VSS2 Video Sync Sensor i Table of Contents VSS2 Video Sync Sensor Product Information Product Information The AM

FIG. 1 shows the front and rear panel views. ID button Status LED IR Receiver Ethernet Ethernet Speed and S-Video OUT IR/Serial port Analog stereo audio Link Activity LEDs RS232/422/485 port OUT (BNC) (front) LCD Displa LCD DisplaLCD Display yy Composite Input/Output port 12 VDC Power (rear) FIG. 1 MAX-CSD10 Video Decoder (front and rear views) Note: This unit can be mounted onto either a flat surface or into an equipment rack by first removing the front screws and then attaching it to an AC-RK.