Stimmen - 5, Durchschnittliche Bewertung: 3.2
(
)
)
|
Anleitung Zusammenfassung
1. Cut out the surface for the WDS using the dimensions shown in installation diagram SP-5965-01 (reproduced in FIG. 11 on page 10). It is recommended that you cutout the surface slightly smaller than what is outlined in the installation drawings so that you can make any necessary cutout adjustments. Be sure to cut out the four notches along the sides to accommodate the four drywall expansion clips (included). When installing the four #6-32 Mounting Screws in Step 3, turn the screwdriver gently to engage the first one or two threads of the screw and make sure that the screw is being driven straight through the holes in the Mounting Tab (FIG. 10). If the screw is found to be entering the Mounting Tab an angle, back it out of the hole immediately and try again to avoid damaging the MVP-WDS. FIG. 10 Installing four #6-32 Mounting Screws in Step 3 MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 2. Thread the USB and Power cables through the surface opening, leaving enough slack in the wiring to accommodate re-positioning of the unit. 3. Connect the 2-pin power connector and USB cables to the WDS. The WDS must be installed with these attached. The USB connectors can be from either a USB extension cable, or a wireless USB RF transmitter. Verify that the terminal end of the power cable is not connected to a power source before plugging in the 2-pin power connector. 4. Install the four sets of drywall screws and expansion clips into the four oval notch locations along both sides of the main unit (FIG. 12). .25 [6MM] TYP 11.06 [281MM] 12.70 [323MM] BEZEL OUTLINE 8.63 [219MM] BEZEL OUTLINE 2X .52 [13MM] 1.00 [25MM] TYP 7.91 [201MM] 2X .22 [5MM] FRONT BEZEL OUTLINE CUTOUT 4X R.13 [3MM] MAX RADIUS IN CORNERS R.13 [3MM] TYP THESE NOTCHES ARE ONLY NEEDED IF UNIT IS INSTALLED USING DRYWALL EXPANSION CLIPS (4 PROVIDED) FIG. 11 MVP-WDS Wall Mount cutout dimensions using expansion clips 5. Carefully insert the main unit (with expansion clips) into the cutout so that the Mounting Tabs on the MVP-WDS lie flush against the wall. MVP-WDS Wall Docking Station for MVP Panels MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box MVP-WDS Wall Docking Station for MVP Panels 11 6. Tighten all four drywall clip sets (screws and clips) until both Mounting Tabs are securely fastened and flush against the wall. 7. Follow the steps outlined in the Replacing the Faceplate on the MVP-WDS section on page 13 to angle the MVP Support Cradle forward and re-install the faceplate. Installing the MVP-WDS Into a Flat Surface Using Mounting Screws Use #4-40 Mounting screws (not included) to mount the WDS to a flat surface, through the two sets of holes located on the sides of the WDS. .. Refer to SP-5965-01 for detailed installation dimensions (reproduced in FIG. 13). .. It is recommended that you cutout the surface slightly smaller than what is outlined in the installation drawings so that you can make any necessary cutout adjustments. .. The outer frame Mounting Tabs must be installed so that they are flush against the mounting surface. 1. Cut out the surface for the MVP-WDS docking station using the dimensions shown in FIG. 13. FIG. 12 MVP-WDS installation configuration for drywall surfaces B - MVP-WDS (Main unit) Install the four included drywall clip sets Four notches are required A - Faceplate Mounting Tab Die Cut Foam covers (2) at these locations to accommodate the four expansion clips (included) #6-32 Faceplate Security Screws (2) Replacement drywall clip sets cab be ordered from AMX. MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box R.13 [3.2MM] MAX RADIUS IN 4 CORNERS CUTOUT FRONT BEZEL OUTLINE 11.06 [281MM] 12.70 [323MM] BEZEL OUTLINE THESE 4 HOLES ARE ONLY REQUIRED WHEN MOUNTING UNIT TO A SOLID SURFACE (PODIUM, DESK, ETC). SECURE UNIT WITH #4 SCREWS 8.63 [219MM] BEZEL OUTLINE 12.10 [307MM] 1.19 [30MM] TYP 5.54 [141MM] .52 [13MM] TYP 7.91 [201MM] FIG. 13 MVP-WDS Wall Mount cutout dimensions using solid surface screws 2. Thread the USB and Power cables through the surface opening, leaving enough slack in the wiring to accommodate any re-positioning of the unit. 3. Connect the 2-pin power connector and USB cables along the right side of the (un-powered) MVP-WDS. The faceplate must be removed prior to any surface installation. .. Verify that the terminal end of the power cable is not connected to a power source before plugging in the 2-pin power connector. .. The USB connectors can be from either a USB extension cable, or a wireless USB RF transmitter. Don’t disconnect the PWR and USB connectors from the MVP-WDS. The unit must be installed with these attached. 4. Test the Power and USB connections before fully installing the WDS. Refer to the LED Indicators table on page 3 for blink pattern information. Applying power to the MVP-WDS causes the MVP Support Cradle to retract back into docking station. 5. Disconnect the terminal end of the power cable from the connected power supply. 6. Carefully insert the main unit into the cutout u...