182713 Retain This Manual In A Safe Place For Future Reference American Dispensing Company products embody advanced concepts in engineering, design, and safety. If this product is properly maintained, it will provide many years of safe, efficient, and trouble-free operation. ONLY properly licensed technicians should service this equipment. Observe all safety precautions displayed on the equipment or specified in the installation/operator's manual included with the water vending machine. UND

Contents Names of the parts Safety precautions The musts in using Using sequence Trouble-Shooting *Answers to question Packing list *Specification Names of the parts Cover of the spin tub Knob of spin timer Inner coverPanel support Water-filling entrance Control panel Power line Handle Spin tub Drain hose Back cover Cabinet Base frame Fixing leg (four pieces) Note:The figures in this manual can only be regarded as diagrammatic sketches. Please understand that, due to constant improvement of desi

When the dryer stops, the dampers automatically close to prevent drafts and the entrance of insects and rodents. To avoid restricting the outlet, maintain a minimum of 12 inches (30.5cm) clearance between the vent hood and the ground or any other obstruction. The vent flap should be able to move freely. Although vertical orientation of the exhaust system is acceptable. Certain extenuating circumstances could affect the performance of the dryer: 1. Only rigid metal duct work should be used. 2. Ve

Refer to the electrical requirements in this manual for The proper power cord to be purchased. 3. A UL approve strain relief must be installed onto power cable. If the the strain relief is not attached, the cord can be pulled out of the pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. 4. Do not use an aluminum wire receptacle with copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and aluminum and can caus

Do not usean adaptor plug or extension cord or remove grounding prong from electrical power cord. Failure to followthiswarning can cause serious injury, fire or death. ELECTRIC DRYERS: 14-30R © DRYER FUSED30 AMP 120/240 V OR 120/208 V WALL DRYER RECEPTACLE SERVICE CORD CORRECT Use this way ONLY GAS DRYERS: Grounding type wall receptacle grounding plug CORRECT Use this way ONLY Note: The instructions appearing in this Owner's Guide are not meant to cover every possible condition and situation tha

However, a preoperational test should be performed before the dryer is publicly used. It is possible that adjustments have changed in transit or due to marginal location (installation) conditions. Turn on electric power to the dryer. Refer to the operating instructions for starting your dryer. Open all shutoff valves. When a gas dryer is first started (during initial start-up), it has a tendency not to ignite on the first ignition attempt. This is because the gas supply piping is filled with

On a call for heat, a 24 volt signal is applied to the 3-way/2-position solenoid valve. This signal switches th. valve so that compressed air is sent to the pistons. The piston rods extend, pushing the hinged steam dampe. plate to the open position. This allows room air to be drawn through the hot steam coil and then through th. tumbler (basket). When the temperature set point has been reached, the 24 volt signal is removed from the solenoid valve, so tha. the solenoid valve blocks the air suppl

113604-4 American Dryer Corporation 88 Currant Road Fall River MA 02720-4781 USA Telephone: +1 (508) 678-9000 / Fax: +1 (508) 678-9447 e-mail: techsupport@amdry.com Retain This Manual In A Safe Place For Future Reference Please read this manual carefully to thoroughly familiarize yourself with the Phase 8 microprocessor controller (computer) system features, operational instructions, and programming characteristics. This manual contains important information on how to employ all the features of

If the menu contains a list of items that will lead to a sub-menu, then the items will be listed in ascending numbered order starting at one. Once the item is selected and entered, the controls will go to the sub-menu. If the menu item does not lead to a sub-menu, the items will only be listed and not numbered. When the item is selected and entered, the selected item will become highlighted. Some of these items without a sub-menu do contain selectable parameters. These parameters will be viewed