Hardware Needed for Step 3: 2 (#22) Bolts 2 (#24) Nuts 2 (#23) Washers 2 (#23) Washers Step 4: Assemble Wheel Axle Supports As shown in Figure 4 below, connect together the 2 Wheel Axle Supports (#4) using 8 (#25) Bolts, 8 (#23) Washers, and 8 (#24) Nuts. DO NOT TIGHTEN BOLTS—leave bolts very loose for inserting axle and tongue in Step #6. Hardware Needed for Step 4: 2 (#4) Wheel Axle Supports 8 (#25) Bolts 8 (#23) Washers 8 (#24) Nuts Page 6 Step 5: Attaching Wheel Axle Supports To Bottom Panel

Log length should be kept to 24” or less.. 4 TOWING SAFETY. • Do not allow persons to ride on splitter. Do not carry any cargo or wood on your. splitter. It may fall off and endanger vehicles that are following you.. • Be sure support leg is in the travel position and coupling secure. This must also. be retracted so not to interfere while towing. Retract support leg by removing. pin, sliding up, and replacing pin.. • Never exceed 45 MPH while towing your splitter. Be extra cautious when. traveli

LS722HSTARTING SERIAL #: L206-010001LS728HSTARTING SERIAL #: L206-010001LS10528HSTARTING SERIAL #: L206-010001LS12534HSTARTING SERIAL #: L206-010001LS12534H12VSTARTING SERIAL #: L206-010001IMPORTANTswisherinc.comRev. 06-164swisherinc.comRev. 06-164 Model LS12534H Shown LOG. SPLITTER Safety Assembly Operation Service and Adjustment Repair Parts 1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093 PHONE 660-747-8183 . Made In The FAX 660-747-8650 USA Manufacturing quality lawn care equipment since 19

. OD16 –FUEL SHUT OFF DECAL OD07 –COLD WEATHER DECAL OD12 – HYDRAULIC FILL PLUG OD23 – TOW POSITION DECAL DECAL OD22 – POSITION LOCK DECAL OD08 – OPERATOR INSTRUCTION DECAL OD09 – DANGER/POSITION LOCK DECAL 10 31 SEE DETAIL 1 2 3 B 4 5 6 7 8 9 10 A A 11 16 15 14 13 12 18 17 8 20 25 21 23 24 26 27 22 22 22 28 29 6 25 39 33 34 35 35 36 30 42 SEE DETAIL 41 40 38 37 43 44 45 46 47 48 49 50 42 16 51 18 52 54 53 52 57 56 49 6 5 57 B FENDERS ONLY ON LS11534 MODEL 190 58 32 55 19 ASSEMBLY DETAIL LS622,

Color cannot be guaranteed upon service parts. ITEM NUMBERDESCRIPTIONPART NUMBER29MOTOR BASE / AXLE729730TIRE / WHEEL729631COTTER PINNB63332WHEEL DUST COVER2203DC33CASTLE NUT2203CN34WASHERNB18435TAPERED BEARING2203B36BEARING SEAL2203S37BELT64438IDLER ARM6681TK39CLUTCH LEVER735840SPRING682S413/8-16 JAM NUTNB17442HARDENED WASHERNB196433/8-16 X 2 1/2 GR5 BOLTNB619445/16-18 FLANGE NUTNB17045IDLER SPRING MOUNT204646WIRE LINK FOR IDLER SPRINGBRS6H47SHOULDER BOLTNB22048IDLER PULLEYB52749WASHERNB27250BE

Color cannot be guaranteed upon service parts. ITEM NUMBER. DESCRIPTION PART NUMBER 107 3/8-16 X 3 1/2 GR5 BOLT NB649 108 3/8-16 X 3 GR5 BOLT NB164 109 1/2-13 X 3 1/2 GR5 BOLT NB577 110 1/2-13 X 1 1/4 GR5 BOLT NB647 112 3/8-16 X 1 GR5 BOLT NB604 113 5/16-18 X 1 GR5 BOLT NB143 114 5/16-18 X 3/4 FLANGE BOLT NB596 115 #14X 3/4 SELF TAPPING SCREW NB161 116 SHOULDER BOLT NB220 117 3/8-16 X 2 1/2 GR5 BOLT NB619 119 3/4-10 X 7 1/2 GR5 BOLT NB655 120 1/4-20 X 1 GR5 BOLT NB102 121 5/16-18 X 4 GR5 BOLT NB

• ONLY operate splitter on level ground with wheels blocked, not on the side of a hill. It could. tip, or rolling logs, poor footing, etc. could cause an accident.. 3 • NEVER operate your splitter near a flame or spark. Hydraulic oil and gasoline are flammable and can. explode.. • NEVER fill gas tank while the engine is hot or running. Allow the engine to cool before refueling.. • This unit is equipped with an internal combustion engine and should not be used on or near any. unimproved forest-co

After the hydraulic reservoir and the engine. crankcase are filled correctly with their respective oils, start the engine. Remember to set the throttle and turn on. the fuel shut-off valve. The hydraulic pump should prime itself. With the engine running, move the hydraulic. valve lever toward the wedge. This will cause the cylinder to extend and expel air. When the cylinder is fully. extended, retract it. Repeat this procedure several times. (An erratic movement of the cylinder and wedge indicat