This pump will fit most Manitowoc ice machines. The discharge port located on the base of the water pump can be rotated, if necessary, for proper positioning in the ice machine. If it is required to rotate the water pump, remove the three machine screws from the pump, turn the base to the desired position, and reinsert the screws. The positioning holes are spaced every 60° in the water pump. When installing this water pump, remove the water flow clamp from all ice machines except the regular c

It will extend from the left sidewall past the water inlet fitting. 1. Remove screws (right and left side) that secure the evaporator to the bulkhead. 2. Remove three screws located between the evaporator and water inlet line. Remove the screw holding the water inlet fitting. 3. Determine bin switch wire location and cut a slot in the top edge of the Mylar strip (adhesive edge = top). 4. Apply silicone sealant at the bin switch wire entrance and the left side corner (4” each direction) wher

It will extend from the left sidewall past the water inlet fitting. 1. Remove screws (right and left side) that secure the evaporator to the bulkhead. 2. Remove three screws located between the evaporator and water inlet line. Remove the screw holding the water inlet fitting. 3. Determine bin switch wire location and cut a slot in the top edge of the Mylar strip (adhesive edge = top). 4. Apply silicone sealant at the bin switch wire entrance and the left side corner (4” each direction) wher

It will extend from the left sidewall past the water inlet fitting. 1. Remove screws (right and left side) that secure the evaporator to the bulkhead. 2. Determine bin switch wire location and cut a slot in the top edge of the Mylar strip (adhesive edge = top). 3. Apply silicone sealant at the bin switch wire entrance and the left side corner (4” each direction) where the base and bulkhead meet. 4. Pull evaporator away from bulkhead. Place bottom of Mylar strip in sump trough and slip up be

Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 Web Site - Rev. 8016483 02/03/05

COMPRESSOR REPLACEMENT INSTRUCTIONS 1. Remove old compressor. Unsweat all tubes from the old compressor. Do not cut them off. 2. Remove the start capacitor. 3. Remove the start relay. Note: If the old compressor was a Copeland model: • Cut 2” off of the suction line. • Remove the three compressor leads from the ice machine. • Remove the two remaining leads from the start relay from the ice machine. • Install six new wires (included in kit) following wiring diagram (included in kit). 4.

Replace the screws along the bottom of the bulkhead. Attach the side cycolac pieces by removing the protective backing from the double-face tape (already on cycolac sides) and press into place. 7. Seal along the entire top edge and corner joints of cycolac panels. Wipe clean any excess RTV sealer that may be on the cycolac panels. Let the RTV sealer dry for approximately one hour. 8. Install water trough, float valve, water pump, water distribution tube assembly, water curtain, and front suppo

Attach the side cycolac pieces by removing the protective backing from the double-face tape (already on cycolac sides) and press into place. 7. Seal along the entire top edge and corner joints of cycolac panels. Wipe clean any excess RTV sealer that may be on the cycolac panels. Let the RTV sealer dry for approximately one hour. 8. Install water trough, float valve, water pump, water distribution tube assembly, water curtain, and front support angle. When installing the water trough, you may h

Let the RTV sealer dry for approximately one hour. 8. Install water trough, float valve, water pump, water distribution tube assembly, water curtain, and front support angle. When installing the water trough, you may have to slot the mounting holes on the ends of the water trough to allow for the thickness of the cycolac panel on the bulkhead rear. Manitowoc Ice, Inc. 2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/