Location of Boiler The installation of the 1001 must be on a suitable non-combustible load bearing wall which will provide an adequate fixing for the boiler mounting bracket assembly. The location should be in an area where the water pipes will not be subjected to frost conditions. In siting the combination boiler the following limitations must be observed: The combination boiler may be installed in any room or internal space, although particular attention is drawn to the requirements of the cur

TROUBLESHOOTING IGNITION SYSTEM The control system has several features to aid in troubleshooting problems which may occur during operation. If a fault occurs, the Display Board contains sixteen (16) red fault LED indicators to help pinpoint the source of failures. In addition, the display will inform the user on which stage the failure occurred by illuminating a red Stage LED. In cases where the problem persists to lockout, the appropriate red LEDs will remain illuminated and a three digit erro

In the absence of local codes, the installation must comply with the latest editions. In the United States: The National Fuel Gas Code, ANSI Z223.1/NFPA 54 and the National Electric Code, NFPA 70. In Canada: The installation Code CAN/CSA B149.1 and .2 (latest edition) and the Canadian Electric Code, CSA C22.2. These are available from the Canadian Standards Association, 8501 East Pleasant Valley Road, Cleveland, OH 44131, USA, or, Canadian Gas Association Laboratories, 55 Scarsdale Road, Don Mil

192386 2 7................Washer, Flat #8 SST................................................................... 191768........................191768.................... 191768 2 8................Restrictor-Air, Top Cover.......................................................... 191926-1 .................... 191926-1 ................ 191926-1 *Item Not Illustrated. LW Models Note: Replacement housing assemblies (item 10) are currently all steel type. When replacing the housing assembly both

....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

If a trap malfunctions, the condensate can be passed to the return unit at a much higher temperature causing the return unit to fail. When using Bryan Condensate Transfer Stations as the return unit, this problem is overcome because they are designed to eliminate cavitation at higher temperatures. In addition, Bryan Condensate Transfer Stations are designed to handle the higher load placed on them during cold starts and are supplied with reliable pumps that are designed to handle hotter water an

5510 (1/01) BRYAN STEAM Compact Boiler Feed Systems Capacities from 20 to 80 boiler HP for 15 through 150 PSI boilers The Bryan compact boiler feed system requires a minimal amount of boiler room space while providing many of the same rugged features as competitive stand-mounted feed systems. Performance Features • Designed to feed 15 through 150 PSI design boilers • Atmospheric tank built from heavy 1/4" minimum steel thickness • Tank sizes from 20 to 80 gallons • Designed to feed 20 t

If the unconfined space is within a building of tight construction (buildings using the following construction; weather stripping, heavy insulation, caulking, vapor barrier, etc.), air for combustion, ventilation, and draft hood dilution must be obtained from outdoors or spaces freely communicating with the outdoors. The installation instructions for confined spaces in tightly constructed buildings must be followed to ensure adequate air supply. CONFINED SPACE (a) U. S. INSTALLATIONS When drawin

CONSULT FACTORY FOR CERTIFIED DIMENSIONS. 5. ALL FLANGES ARE 150# UNLESS OTHERWISE NOTED, FLANGES TO STRADDLE CENTER LINE. PLAN VIEW FR°NT VIEW RIGHT SIDE VIEW REAR VIEW 1. PROBE TYPE AUX. L.W.C.O. 6. JACKET ACCESS PANELS 11. DRAIN/ BLOWDOWN - 1" NPT 16. HEIGHT OVER JACKET 2. FORCED DRAFT BURNER 7. PRESSURE GAUGE 12. BURNER CENTER LINE 17. HEIGHT OVER SUPPLY 3. RELIEF VALVE 8. CLNOUT./INSP. OPNG.-1 1/2"NPT 13. OIL PUMP LOCATION 18. MINIMUM SAFE WATER LEVEL 4. ASME NAMEPLATE 9. ELEC. ENCLO

CONSULT FACTORY FOR CERTIFIED DIMENSIONS. 5. ALL FLANGES ARE 150# UNLESS OTHERWISE NOTED, FLANGES TO STRADDLE CENTER LINE. PLAN VIEW FR°NT VIEW RIGHT SIDE VIEW REAR VIEW 1. PROBE TYPE AUX. L.W.C.O. 6. JACKET ACCESS PANELS 11. DRAIN/ BLOWDOWN - 1" NPT 16. HEIGHT OVER JACKET 2. FORCED DRAFT BURNER 7. PRESSURE GAUGE 12. BURNER CENTER LINE 17. HEIGHT OVER SUPPLY 3. RELIEF VALVE 8. CLNOUT./INSP. OPNG.-1 1/2"NPT 13. OIL PUMP LOCATION 18. MINIMUM SAFE WATER LEVEL 4. ASME NAMEPLATE 9. ELEC. ENCLO