Alle Rechte vorbehalten Bass-Boost einstellen Bass-Boost optimiert die Leistung des subwoofers und ermoglicht eine stufenlose Anpassung der tieftonverstarkung fur die hinteren Kanale Bass-Boost ist von 0 bis 18 dB einstellbar und um 45 Hz zentriert Zunachst ist der Q-Faktor sehr niedrig (breit) Wenn der Boost angehoben wird, steigt der Q-Faktor (enger) Dadurch kann der Verstarker akustische schwachstellen in Ihrem Fahrzeug kompensieren Die Art des verwendeten Gehauses, die Auslenkung des subwoof

Alle Rechte vorbehalten 56 VeRstARKeRVeRKABeLUnG Stromanschlusse fur den XTR5001, XTR10001 und XTR15001 • stromanschlusse mit bis zu 4 AWG Drahtdicke • 4 AWG strom- und erdungskabel fur optimale Leistung empfohlen • Durch sicherungsfassung 12V+ an die Batterie anschlie.en Dieser Anschluss liefert +12V strom an den Verstarker • Das stromkabel muss in hochstens 30 cm entfernung von der Batterie abgesichert werden • Der Verstarker muss an einem guten Chassis-erdungspunkt geerdet werden, der nicht z

(Watt) 500 x 1 1000 x 1 1500 x 1 Verstarker-Wirkungsgrad 80 % 80 % 80 % Rauschabstand bei nennleistung und niedrigster Impedanz >65 dB >65 dB >65 dB externer Bruckenmodus nein nein nein Fernverstarkungsfunktion Ja (uber RGC2) Ja (uber RGC2) Ja (uber RGC2) Verzerrung bei nennleistung 0,5 % Gesamtklirrfaktor und Verzerrungen (tHD+n) Frequenzgang 20 Hz bis 300 Hz +/- 2,5 dB 20 Hz bis 300 Hz +/- 2,5 dB 20 Hz bis 300 Hz +/- 2,5 dB Lineare Bandbreite 20 Hz bis 300 Hz +/- 3 dB 20 Hz bis 300 Hz +/- 3 dB

Ground (10.5-16V) 270 x 36 x 330 10.63 x 1.42 x 13 features and controls 18dB 0dB HPF LPF FULL HPF LPF FULL 18dB 0dB BASS BOOST X-OVER BASS BOOSTX-OVER CH 1/2 CH 3/4 4 ch amp PLA-4120 PLA-4120 9 electrical connections 2 ch amp • PLA-2230 • PLA-2260 PLA-2230 PLA-2260 10 PLA-4120 electrical connections PLA-4120 electrical connections 4 ch amp PLA-4120 11 stereo input connections 2 ch amp • PLA-2230 • PLA-2260 12 PLA-2230 PLA-2260 mono input connections 2 ch amp • PLA-2230 • PLA-2260 13 PLA-2230 PL

on your purchase of a Pyle Chopper Series amplifier. This amplifier extends the Pyle tradition into a totally new series of amps, designed from the ground up to deliver the power, performance and flexibility the modern car audio enthusiast demands. When you check the list of features offered by the PLA-1200, PLA-2230, PLA-2260, and PLA-4120 you’ll know you made the right choice with a Pyle Chopper amplifier. table of contents table of contents general features 2-3 features and specifications PLA

When using stereo, bridge, mono function, the connect model must be same than model switch selected. When output high-power signal continuously, the amplifier should be has speedup in the cooling fan, it may be have low noise produce in this equipment, it is normally. The general gain of the amplifier can be adjust by gain knob, the input level have 0.77V, 1.4V, full-power out and fixed 26dB gain 3 band should be selected. Donr vent of rear panel. When clear-up the cover of the equipment, you mu

PQA series amplifiers has full-protection, including: Soft start function to prevent wave shock at power-on. Delay function for prevent shock at switch power on. DC protection. Over-electric current protection. Cut-wave protection. Over heat protection. ATTENTION Never put any parts on the top of the amplifier. Using fixed power socket that must be has enough capacity to prove power. Never switch the power on and off continuously at the same time. Donruction in the air vent of front panel. Input

.Ensure the amp is adequately ventilated, with free airflow to the front and rear panels. Keep away from other heat sources. If the amps are mounted in a rack with other amps, ensure there is adequate cool air flow front and rear. Note that air is drawn in through the back panel, and exhausted through the front panel. .NEVER cover the amplifiers, as they may overheat. .PQA power amplifiers are designed to fit standard 19 racks, with a 2U height and 17 depth. We recommend the use of rear rack sup

This warranty is limited to the original retail purchase. Should the product fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of Pyle. To obtain warranty service you must first call our Consumer Return Hotline number at (718) 236-6948 to obtain a Return Authorization number. This R.A.# must appear on the outside of your package and on all paperwork relating to your return. When returning a product to us for warranty service it

This innovative system has been designed a 12 volts DC negative ground power supply. Easy installation with mounting hardware is provided. The PLMRA 400 has two input levels. The high or low impedance input can be connected to units which incorporate BTL circuity or common-ground types. (3) © (p nf CTT ^ ^ ^ C= c= — 3 CM/L 4 CH/ft — HIGH INPUT LEVEL to)) ■ (Cl CH/L 2CM/R LEVEL HIGH INPUT O 0 =3 iP ETr c= c= c= c= ©04-12V GND REMOTE*^ E ,-SPEAKERS- 4 CM/R 3CM/L tCH/R 1CH/L © © =3