This is useful for connection of component speakers or coaxials to this channel pair in a bi-amplified system. “x10” (High-Pass): Configures the filter to attenuate frequencies below a frequency TEN TIMES HIGHER than the indicated filter frequency at a rate of 12dB per octave. This is useful for connection of tweeters to this channel pair in a tri-amplified system. Channel 3 & 4 Filter: 12dB/octave High-Pass or Bandpass Filter “Off”: Defeats the filter completely, allowing the full range of freq

Dieser Monokanal kann sowohl nur das rechte Kanalsignal, als auch das linke Kanalsignal oder die Summe aus beiden Kanalen beinhalten. Um eine dieser Moglichkeiten zu gewahrleisten, sollten Sie eine der beiden folgenden Anweisungen befolgen: 1) Nur das linke ODER das rechte Kanalsignal: Falls Sie wunschen, dass nur jeweils das linke oder rechte Kanalsignal im gebruckten Monomodus ausgegeben wird, sollten Sie einen “Y-Adapter” verwenden, der das jeweils gewunschte Audiosignal splittet. Dies ist nu

4) Verlegen Sie die Audio-Signalkabel und die Remote-Steuerleitung vom Steuergerat zum Einbauort des Verstarkers. 5) Verlegen Sie die Lautsprecherkabel vom Lautsprecher zum Einbauort des Verstarkers. 6) Danach suchen Sie einen soliden metallischen Massepunkt in der Nahe des Verstarkers und schlie.en Sie das Massekabel (Minus) mit geeignetem Anschlusszubehor dort an. Benutzen Sie dafur den selben Kabel-Querschnitt wie der des verwendeten Stromversorgungskabels fur den Pluspol (mind. 16 mm2). Acht

Bitte schranken Sie das Horen von Musik bei hohen Lautstarken entsprechend ein. Bedienen und benutzen Sie bitte Ihr Audio- System wahrend des Fahrens nur so, dass notwendige Gerausche zum sicheren Fahren Ihres Fahrzeugs immer noch wahrgenommen werden konnen (Hupe, Warnsignale, Sirenen etc.). SeRIENNUMMER: Fur den Fall eines Reparaturvorgangs oder eines Diebstahls, bitten wir Sie die Seriennummer des Gerats zu notieren. Notieren Sie diese im unten vorgesehenen Feld. Sie finden die Seriennummer au

7) Securely mount the amplifier. 8) Connect the positive and negative power wires to the amplifier. A fuse near the amplifier is not necessary if the XD200/2 is the only device being run from the fused main power wire. If the fused main power wire is shared by the XD200/2 and other amplifiers or devices, fuse each amplifier/device within 12 inches (30 cm) of wire length, via a fused distribution block or multiple individual fuse blocks/on-board fuses. 9) Connect the remote turn-on wire to the am

4. Connect the REMOTE terminal to an external switch for positive 12V turnon-off. This may be connected to the head unit power antenna lead. Installation Precautions This amplifier comes complete with all mounting harware required. Please remember that this is a high-power unit, which generates considerable electrical energy and heat. Therefore, be sure to install the unit in a place with sufficient airflow, a minimum of dust, and no moisture. Allow enough space around the cooling fins to permit

Should this occur, the PROTECT LED will be illuminated. At that time, it is important that you check to determine what has caused the protection circuitry to become activated. If the amp shut off because of a thermal overload, allow it to cool down before attempting to restart. If the shutdown occured because of an input overload, or speaker short circuit, be sure to correct these conditions before attempting to restart the amp. To reset the amp, turn the REMOTE power off and on again. Power LED

If distortion is present, reduce thesetting of this control. 4 Power Supply Terminals3 Protects the amplifier as well as the automobile electricalsystem from short circuit conditions. Fuse2 These terminals are 14K Gold plated for high conductivityand minimum impedance loss. The terminals faceupwards for easy wiring in tight situations. Speaker Terminals112 Plug in the Remote Bass Boost Control wire in here. 13 Remote Bass Boost REMOTE BASS BOOST CH2 CH1 LOW IN CH4 CH3 LOW IN HI IN CH4 CH3 + - -

• Gold Plated Terminals for Speaker Output and Power Input. • Thermal, Overload and Short Protection• Variable Sub-sonic Filter (15Hz~40Hz, 24dB/Octave) • Variable Low-pass Filter (20Hz~250Hz, 24dB/Octave) 5 13 2 874 6 +18db0BASSBOOST 35 400 HzLPF HPF 80 2.5k Hz LEVELMIN MAX FULL HPFLPFFREQ. GROUND +12V BATT REM FUSEL RBRIDGED+ - - + - + SpecificationsOUTPUT POWERRMS @ 4 OHMSRMS @ 2 OHMSMAX OUTPUTBRIDGE MODEFREQUENCY RESPONSEINPUT IMPEDANCELOW LEVEL INPUTSHIGH LEVEL INPUTSINPUT SENSITIVITYLOW LE

If hiss/noise disappears, go on until the faulty/noisy component is found. • It is best to set the amplifier's input level as insensitive as possible. The best subjective S/N ratio is obtainable this way. Try to drive as high a signal level from the head unit as possible. Protection LED comes on when the amplifier ispowered up. • Check for shorts on speaker leads. • Check that the volume control on the head unit is turned down low. • Remove speaker leads, and reset the amplifier. If the Protecti