Insert MOUNTING ROD ASSEMBLY (1) into METAL HANDLE (3), HANDLE COLLAR (4) and O-RING (5). 3 2 6 1 4 7 Thread HANDLE ASSEMBLY (6) into ball of HANDLE BASE (7). Apply pressure to the MOUNTING ROD ASSEMBLY (1) while turning the HANDLE COLLAR (4), in order to tighten firmly. 5 SERVICE ALIGN HANDLES 11 To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Pull out INDEX CAP and remove HANDLE SCREW. Remove SPRING CLIP. Lift STOP WASHER, turn 90° and replace. Replace S

Develop a thorough understanding before starting the commissioning procedure. This manual is to be used by the commissioner as a guide. Each installation is unique, only general topics are covered. The order in which topics are covered may not be those required for the actual commissioning. © 2006 McQuay International Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Acronyms/Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Getting St

Concealed Mounting: No exposed set screws. Materials of Construction: Body - zinc. Escutcheon - brass. Index button -porcelain. Toothbrush Holder and Tumbler - clear glass. Easy to Install SUGGESTED SPECIFICATION: Tumbler/Toothbrush Holder shall feature heavy-duty construction. Shall feature concealed mounting. Toothbrush Holder and Tumbler shall be clear glass. Tumbler/Toothbrush Holder shall be American Standard Model # 6761_. - E29 - © 2008 AS America Inc.

If the connection leaks after hand tightening, replace the supply line. If the connection continues to leak with the new supply line, replace the fill valve. Warranty is void if any type of sealant is used on the water supply connection. 7301102-100 Rev. K - 2 10 VALVE BODY ADJUSTABLE HEIGHT TOP CONE WASHER COUPLING NUT (HAND TIGHT ONLY) FILL VALVE FLOAT CUP CRITICAL LEVEL MARK ("C.L.") MUST BE 1" ABOVE OVERFLOW PIPE LOCK NUT WATER LEVEL ADJUSTMENT ROD TANK LEVER FLUSH VALVE ARM NIPPLE PARTS FOR

If the connection leaks after hand tightening, replace the supply line. If the connection continues to leak with the new supply line, replace the fill valve. Warranty is void if any type of sealant is used on the water supply connection. 7301102-100 Rev. K - 2 10 VALVE BODY ADJUSTABLE HEIGHT TOP CONE WASHER COUPLING NUT (HAND TIGHT ONLY) FILL VALVE FLOAT CUP CRITICAL LEVEL MARK ("C.L.") MUST BE 1" ABOVE OVERFLOW PIPE LOCK NUT WATER LEVEL ADJUSTMENT ROD TANK LEVER FLUSH VALVE ARM NIPPLE PARTS FOR

Go to our website at for more solutions to toilet problems. © 2001 Fluidmaster, Inc. ® Registered trademark of Fluidmaster, Inc. Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster, Inc. 30800 Rancho Viejo Road San Juan Capistrano, CA 92675 (949) 728-2000 (800) 631-2011 LIFT ARM FIRST 7301102-100 Rev. K - 3 RE

Go to our website at for more solutions to toilet problems. © 2001 Fluidmaster, Inc. ® Registered trademark of Fluidmaster, Inc. Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster, Inc. 30800 Rancho Viejo Road San Juan Capistrano, CA 92675 (949) 728-2000 (800) 631-2011 LIFT ARM FIRST 7301102-100 Rev. K - 3 RE

Go to our website at for more solutions to toilet problems. © 2001 Fluidmaster, Inc. ® Registered trademark of Fluidmaster, Inc. Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster, Inc. 30800 Rancho Viejo Road San Juan Capistrano, CA 92675 (949) 728-2000 (800) 631-2011 LIFT ARM FIRST 7301102-100 Rev. K - 3 RE

b. Loosely install retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up! CLOSET BOLT NUT TAPERED WASHER FLANGE INSTALL CLOSET BOLTS Install closet bolts in flange channel, turn 90°, and slide into place 6" (152 mm) apart and parallel to wall. For 4007 Tanks: 12" (305mm) ROUGHING-IN DIMENSIONS: NOTE: Distance from wall to closet flange centerline must be as listed below: © AS America, Inc. 2011 RUBBER GASKET TANK MTG. BOLTS PREINSTALLED 6 7 INSTALL TOILET a. Position toil

(Certain installations may require professional help.) Also be sure your installation conforms to local codes. CAUTION: PRODUCT IS FRAGILE.TOAVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE! NOTE: Pictures may not exactly define contour of china and components. RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level ! 1 REMOVE OLD TOILET a. Close toilet supply valve and fl