x 20.75 Cyl. Assy. Bucket 24314 3.0 Dia. x 30.00 Cyl. Assy. Lift 811572_3/8 x 15" Hose 3/4 MORB x 3/4 SWFJIC 811471 3/8 x 20" Hose 3/4 MORB x 3/4 SWFJIC 811466 3/8 x 24" Hose 3/4 MORB x 3/4 SWFJIC 812947_3/8 x 22" Hose 3/4 SWFJIC x 3/4 SWFJIC 112833 Tubing - Lift Cyl. Bottom Raise 112834 Tubing - Lift Cyl. Top Drop 112937 Tubing - Lift Cyl. Common (31.0") 112835 Tubing - Bucket Cyl. Bottom Rollbk 112836 Tubing - Bucket Cyl. Top Dump 112837 Tubing - Bucket Cyl. Cross Tube 812128 Elbow 90

If the loader is lowered from this position, the bucket will extend as the quick attach contacts the rollback stop and the circuit goes through relief as described in note 2. The relief valve is factory set at 3250 PSI cracking pressure and is capable of bypassing 10-15 GPM. If loader lock-up should occur due to a low tractor relief setting, higher inlet flows or return line restrictions, the relief valve may be backed off slightly until the lock-up condition is overcome (counterclockwise turn

Any sample or model is for illustrative purposes only and does not create an Express Warranty that the goods conform to sample or model shown. t The purchaser is solely responsible for determining suitability of goods sold. This warranty is expressly in lieu of all other warranties expressed or implied. Buhler Manufacturing will in no event be liable for any incidental or consequential damages whatsoever, nor for any sum in excess of the price received for the goods for which liability is clai

. 2. Move and turn tractor at low speed. 3. Carry loader arms at a low position during transport. ■ 4. Lower loader arms, stop engine and lock brakes before leaving operator seat. 5. Do not stand or work under raised loader, unless properly ' supported. 6. Add recommended wheel ballast or rear weight for stability. 7. Move wheels to widest recommended settings to increase stability. 8. Do not handle large round bales or other shiftable objects unless loader is equipped with a grapple fork

Disclaimer Information in this document is subject to change without notice. The material contained herein is supplied without representation or warranty of any kind. The seller therefore assumes no responsibility and shall have no liability of any kind arising from the supply or use of this document or the material contained herein. Trademarks All trademarks mentioned in this document may be the property of their respective owners. November 3, 2003 Rev.20 Safety Instructions For Installation •

They currently use analog cellular or standard phone lines to connect in circuit- switched mode for data transfer. Analog cellular phone service is being discontinued. The combination of the Host RJ-11 IP Gateway, RJ-11 IP Gateway, and the AirLink Raven-E enables remote connectivity between host applications and these remote devices over cellular packet data networks. The RJ-11 IP Gateway provides the bridge between a device requiring an RJ-11 interface and the Raven-E, with its Ethernet interfa

August 9, 2001 Information in this document is subject to change without notice. . Copyright AirLink Communications, Inc, 1993-2001. All rights reserved. Please send comments to: email: pubs@AirLink.com Fax: 510-226-4299 Phone: 510-226-4200 Post: AirLink Communications, Inc. Attention: Technical Publications Dept. 472 Kato Terrace Fremont, CA 94539 AirLink Tech Support can be reached at 510-226-4200 Mon-Fri 9:00a-5:00p Pacific Time. Copyright . 2001 AirLink Communications, Inc. All Rights Reserv

Starting the Setup Wizard manually on Windows PCs After one minute, if the Setup Wizard does not run automatically, follow these steps: 1. Double-click the My Computer icon located on the desktop. 2. Double-click the icon that corresponds to your CD-ROM drive, then double-click Setup.exe. 3. Follow the onscreen instructions. First computer only: After the Setup Wizard completes, the BROADBAND LINK indicator light on the front of the HomePortal flashes green as it attempts to establish a connecti