The Pocket Programmer is intended for use by an installer who is familiar with UPStart and UPB products. It virtually eliminates the need to have a PC with UPStart software and a Computer Interface Module (CIM) at every jobsite. It makes configuring UPB devices from room to room, quick and easy. The UPP may be used instead of UPStart to provide initial configuration steps such as adding devices to a UPB network or disabling dimming allowing a newly installed switch to operate a fluorescent fixtu

THOMAS, ONTARIO, CANADA Printed in U.S.A. eCopyright by the Gorman-Rupp Company OM--04760 SELF-PRIMING CENTRIFUGAL PUMPS INTRODUCTION Thank You for purchasing a Gorman-Rupp Self- Priming Centrifugal Pump. Read this manual carefullytolearnhowtosafelyinstallandoperate yourpump.Failuretodosocouldresultinpersonal injuryordamagetothepump. Asetofthreemanualsaccompaniesyourpump. Eachset consistsof threeparts; theInstallation/ Operation Manual contains essential information oninstallingandoperatingthepu

This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. Multi-Tech Systems, Inc. makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, Multi-Tech Systems, Inc. reserves the right to revise this publication and to make changes in the content hereof without obligation of Multi-Tech

An fault may occur if P 20 and the Assertion switch are not set identically. Note 5 If an EPM that contains data from a previous compatible software version is installed: • The drive will operate according to the previous data, but parameters cannot be changed ( will be displayed if attempted) • To update the EPM to the current software version, set P 99 = 5. The parameters can now be changed but the EPM is incompatible with previous software revisions. ENGLISH Commissioning 4.5.4 PID Parameters

Name Default Selection Assertion Level 2 Low P 20 and the Assertion Level switch must both match the desired assertion level unless P 00, P 2 …P 2 are all set to 0. Otherwise an F.AL fault will occur. 2 High TB- A Input Function TB- B Input Function TB- C Input Function 0 0 None Disables input AUTO Reference: 0- 0 VDC For frequency mode, see P 0...P , For PID mode, see P204…P205, For vector torque mode, see P 0 2 AUTO Reference: 4-20 mA AUTO Reference: Preset For frequency mode see P ...P 7, For

and COTILLION MUSIC, INC. Copyright Renewed All Rights Reserved Used by Permission The Lonely Bull By Sol Lake Copyright © 1962 ALMO MUSIC CORP. Copyright Renewed All Rights Reserved Used by Permission Respect Words and Music by Otis Redding Copyright © 1965 IRVING MUSIC, INC. Copyright Renewed All Rights Reserved Used by Permission Soul Man Words and Music by Isaac Hayes and David Porter Copyright © 1967 ALMO MUSIC CORP. and WALDEN MUSIC, INC. Copyright Renewed All Rights Reserved Used by Permi

To remove the Filter Cover, hold on to the Hair Dryer handle and lift the tab at the base of the Filter Cover with the thumb of your other hand until it releases. Locate the tab at the top of the Filter Cover and slide the tab away from the Hair Dryer to remove the Air Filter Cover. (See Figure A.) Figure A Removing the Air Filter Cover Use a small dry cloth to remove build-up from the Air Filter and Filter Cover. 9 To replace the Filter Cover, Groove align the Filter Cover Guide with the groove

Always "unplug it" immediately after using. 2. Do not use while bathing. 3. Do not place or store appliance where it can fall or be pulled into a tub or sink. 4. Do not place in or drop into water or other liquid. 5. If an appliance falls into water, "unplug it" immediately. Do not reach into the water. WARNING: To reduce the risk of burns, electrocution, fire or injury to persons: 1. An appliance should never be left unattended when plugged in. 2. Close supervision is necessary when this applia

Fast drying. Low General purpose styling. Smoothing medium — fine textured hair. Heating hair set with velcro rollers. Cool Shot Button For longer lasting styles, press for a shot of cool air. The Cool Shot feature operates only while the Cool Shot Button is held down. When it is released, the dryer will return to normal operation. Dual Voltage Switch To change the voltage, use a pen to move the switch to correspond to voltage of the country. Be certain the appliance is unplugged. The 125-volt p