A k. A ^ ■ I IL JÊL T E C H N O L O G I E S Master & Slave Pins Lever £ Pin 1 — Toshiba 1.8” ZIF (Zero Insertion Force) Hard Drive 1. Open the locking lever on the Toshiba 1.8” ZIF hard drive. 2. Slide the flat ribbon cable of the converter into the ZIF connector on the hard drive. 3. Close the lever to secure the ribbon cable connection. Connecting the Toshiba 1.8” ZIF hard drive to a 40-pin IDE connector AA25IDE35 (optional) Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-4

This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try and correct the interference by one or

# Since USB 2.0 Hi-Speed is an evolution of the existing USB 1.1 specification, it is fully forward and backward compatible with current USB systems. # If your computer’s USB controller is only USB1.1 you can only achieve a 4X maximum CD writing speed. # If you do not have a USB2.0 port, you may install an optional USB2.0 adapter or controller (see optional accessories section on page 13) to your computer to achieve the maximum DVD CD writing speed. USB interface cable installation Attach the US

Installing drives into the RAID Tower V Step 1 Use a Philips screwdriver to secure the 3.5” SATA hard drive to the drive tray Step 2 Slide the tray into the Disk Array drive bay. Note: It is recommended to fill up the RAID Tower IX with SATA drives from top to bottom. This is to help in identifying which drives connects to which ports for easier troubleshooting. Note: The 5 port HPMXA system version PCB board is mounted inside the RAID tower and is connected to the multilane bridge that is mount

A single beep will be heard to indicate initialization is completed. The above steps act as a reset. d. Power off the system power. Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: 1 2 3 4 5SW1 BZS EZ M2 M1 M0 1 2 3 4 5SW1 BZS EZ M2 M1 M0 SW1 SW1 1 2 3 4 5SW1 BZS EZ M2 M1 M0 RAID 5 Mode 1 2 3 4 5 SW1 BZS EZ M2 M1 M0 BZS EZ M2 M1 M0 RAID 1& RAID 10 Mode Large Mode 1 2 3 4 5 SW1 1 2 3 4 5 SW1 1 2 3 4 5 e. On the DIP switch, change (M0 to M2) setting to the desired RAID mode u

CardBus mode – move the switch to the side with the DOT indicator Text Box: Text Box: Text Box: CardBus Text Box: PCMCIA Text Box: Front view Text Box: Factory default setting is CardBus mode CardBus/PCMCIA driver Installation For Windows 95, 98, 98SE and Me (Do not run the SETUP program from the driver disk, SETUP Is for DOS or WIN 3.1 using PCMCIA mode only) 1. Power on your system and wait for the Desktop screen. 2. Connect the CardBus/PCMCIA cable and external AC/DC adapter into the back of

We welcome any valuable inputs you can provide us so we can continue to improve our services and products. Please email all your comments to atc@addonics.com or any technical related questions to techinfo@addonics.com. * Make sure you have enough space in your local hard drive. At least 4Gb or higher. The USB cable is an Addonics USB 2.0 interface cable. The process involved A. Set up the USB drives under DOS mode (step 1 - 9) B. Copy folders and files from your Windows installation CD to the ha

ADSA4R-E (4-Port External SATA PCI Controller Card) SPECIFICATIONS INSTALLATIONS Chip Set: Silicon Image Sil3114 integrated host Controller Interface: PCI bus compatible I/O Ports: (4) eSATA Connectors Regulatory approvals: FCC, CE Features: • Up to 150 Mbytes/sec (1.5 Gbits/sec) per port • 4 External SATA (eSATA) ports with the new SATA External connector • Work with any SATA drive • Use as a non-RAID or RAID controller • Built-in RAID 0, RAID 1, RAID 1+0, RAID 1+ S support • Support la

Insert the Gigabit Ethernet ExpressCard Adapter to the system’s ExpressCard slot. Windows 2000, XP & 2003 Driver Installations 1. The Found New Hardware Wizard pops on the screen. Place the Addonics driver disk into the CDROM drive. 2. Found New Hardware Wizard: Can Windows connect to Windows Update to search for software? Select “No, not at this time” Click Next. 3. The Generic Marvell Yukon Chipset base Ethernet Controller is identified. 4. Found New Hardware Wizard: What do you want the

When Windows boots up, “A New Hardware Found” pops on the screen and the Addonics Serial ATA CARDBUS Controller is identified. 2. At the “Add New Hardware Wizard Window, click “Next” 3. Choose “Select for the best driver for your devices”, and click “Next” 4. Insert the Drivers Diskette or Driver Disc and check the “Floppy Drive or CDROM Drive” option. Click “Next” 5. If using a driver that has not been digitally signed by Microsoft, you will be asked if you want to continue the installation