Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Addonics Technologies Dateigröße: 132.3 kb Dateiname: Unterrichtssprache:

A single beep will be heard to indicate initialization is completed. The above steps act as a reset. d. Power off the system power. Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: 1 2 3 4 5SW1 BZS EZ M2 M1 M0 1 2 3 4 5SW1 BZS EZ M2 M1 M0 SW1 SW1 1 2 3 4 5SW1 BZS EZ M2 M1 M0 RAID 5 Mode 1 2 3 4 5 SW1 BZS EZ M2 M1 M0 BZS EZ M2 M1 M0 RAID 1& RAID 10 Mode Large Mode 1 2 3 4 5 SW1 1 2 3 4 5 SW1 1 2 3 4 5 e. On the DIP switch, change (M0 to M2) setting to the desired RAID mode using the diagram below. All settings on the diagram shows • Error buzzer function is ENABLED • EZ function is DISABLED. RAID 0 Mode Clone Mode BZS EZ M2 M1 M0 BZS EZ M2 M1 M0 RAID 3 Mode Individual Drives Mode OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF ON ON ON OFF ON ON OFF OFF ON OFF OFF OFF OFF OFF OFF 1 2 3 4 5 OFFOFF ON OFF OFF ON OFF ON ON BZS EZ M2 M1 M0 Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: RAID Setting Notes: 1 2 3 4 5SW1 When 2 drives are RAID 1& RAID 10 Mode connected to the HPM-XA, and DIP switch is set to this setting, the 2 drives will be configured as a 2-drive RAID1 array. BZS EZ M2 M1 M0 When 4 drives are connected to the HPM-XA, the 4 drives will be configured as a 4-drive RAID10 array. Clone’s action is similar to Clone Mode RAID1. However, all of the 1 2 3 4 5SW1 hard drives will be mirrored. Clone mode is useful especially when users like to copy data from a source BZS EZ M2 M1 M0 hard drive to the drives connected to the HPM-XA. f. Press the RAID setting button with a ball point pen. g. While pressing the RAID setting button turn on the system power where the HPM is connected. The buzzer will sound while holding the RAID setting button. Release it after at least 5 seconds for hardware initialization. A single beep will be heard to indicate initialization is completed. h. Verify if the RAID array is detected by the system. i. If the 5-port HPM-XA is connected to the motherboard onboard SATA, on the CMOS setup utility, the raid array will display as “Addonics H/W RAID5” if setup as a RAID5 array. j. If the 5-port HPM-XA is connected to an eSATA host controller card, on the RAID BIOS, the raid array will display as “Addonics H/W RAID0” if setup as a RAID0 array. k. If booted into Windows, in Disk Drives under Device Manager, the raid array will display as “Addonics H/W LARGE” if setup as a LARGE array. l. Once raid array is verified, you can set the buzzer either ON or OFF. Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: Notes on Spare Drives using the Easy RAID Setting (EZ) When EZ function is ENABLED, the auto-rebuilding to spare drive is automatic. The degraded RAID group will start rebuilding automatically by using the existing spare drive. * Spare drive can be either plugged before RAID building or a new drive can be plug as the spare drive when RAID rebuild is required. A. Which port acts as a spare drive? The last drive will automatically become the spare drive. For a 3-drive RAID5 with spare: Drives connected to SATA ports 1~3 belong to the active RAID5 array and drive connected to port 4 is the spare. For a 4-drive RAID10 with spare: Drives connected to SATA ports 1~4 belong to the active RAID10 array and drive connected to port 5 is the spare. For a 2-drive RAID1 with spare: Drives connected to SATA ports 1& 4 belong to the active RAID1 array and drive connected to port 5 is the spare. B. When will rebuild action start? • When the raid fails and EZ is enabled, the HPM-XA will automatically rebuild the RAID group using the spare. • When the raid fails and EZ is disabled, the HPM-XA will NOT rebuild the raid group unless you install a good drive to replace the failed drive. Connecting the Power Cable and RAID Tower to the Computer Back a. Connect the power cord provided from the wall outlet to the back of the tower. b. Make sure the power is off (power LED light should be off). c. Connect the infiniband cable from the back of the tower to the multilane connector on the computer. Power on/off control Bottom Front a. A main power switch is located at the back of the tower. Turn the switch on. Another auxiliary switch is located on the front of the tower. Power Switch switch (power LED light should be off). HDD LEDs b. Make sure the power is off on the auxiliary c. Power on the tower. Power Connector Power Switch Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: ...

Herunterladen

Geben Sie zwei Ziffern: