Login:

Kobe Range Hoods CH7930SQB

heruntergeladen wurde: 2Dateigröße: 6 mb    Hersteller: Kobe Range Hoods  
Kategorie: Ventilatoren

CH7930SQB CH7936SQB CH7942SQB CH7948SQB CH-179 SERIES – 9” HEIGHT INSTALLATION INSTRUCTIONS AND OPERATION MANUAL MANUEL D'INSTALLATION ET MODE D'EMPLOI INSTRUCCIONES DE INSTALACION Y MANUAL DE OPERACION [ENGLISH] ...................................................................................................................... 1 [FRENCH] ..................................................................................................................... 34 [SPANISH] ..........................

Kobe Range Hoods CH7942SQB

heruntergeladen wurde: 3Dateigröße: 6 mb    Hersteller: Kobe Range Hoods  
Kategorie: Ventilatoren

6. Slide the inner duct cover up 2 inches before sliding the entire duct cover onto the hood. Refer to Figure 19. P4010006 P4250023 Figure 18 Figure 19 7. Adjust the height of the inner duct cover to the duct cover-mounting bracket. Secure the inner duct cover with two (4x8 mm) screws (provided) as shown in Figure 20. P4010005 Attach Together Figure 20 8. Fasten outer duct cover to multi vent exhaust on the hood with four (4x8 mm) screws (provided). WALL MOUNT INSTALLATION – REAR VENT ***This in

Kobe Range Hoods CH7936SQB

heruntergeladen wurde: 7Dateigröße: 6 mb    Hersteller: Kobe Range Hoods  
Kategorie: Ventilatoren

4) Activating any switch on may cause ignition or an explosion. 5) Due to the size and weight of this hood, installation by 2 persons is recommended. ELECTRICAL SHOCK HAZARD – Can result in serious injury or death. Disconnect appliance from electric power before servicing. If equipped, the fluorescent light bulb contains small amounts of mercury, which must be recycled or disposed of according to Local, State, and Federal Codes. COMPONENTS OF PACKAGE (Must keep all material for returns or refund

Kobe Range Hoods CH7948SQB

heruntergeladen wurde: 5Dateigröße: 6 mb    Hersteller: Kobe Range Hoods  
Kategorie: Ventilatoren

Avoid getting cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. Caution: Do not leave on too long as this may cause damage to hood finish. Use soft towel to wipe off the cleaning solution, gently rub off any stubborn spots. Use dry soft towel to dry the hood. 3. DO NOT allow deposits to accumulate or remain on the hood. 4. DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting. 5. DO NOT a

Kobe Range Hoods CH7930SQB

heruntergeladen wurde: 20Dateigröße: 3 mb    Hersteller: Kobe Range Hoods  
Kategorie: Kraftstationen

Light bulbs should be 12V 20W maximum. 5. Using a cloth, hold the new light bulb and push securely into light socket. 6. Return halogen light glass cover to the housing. . 7. Turn range hood ON to test for operation. 20 SPECIFICATIONS MODEL / SIZE CH7930SQB / 30” CH7936SQB / 36" CH7942SQB / 42" CH7948SQB / 48" COLOR Commercial Grade Stainless Steel CONSUMPTION / AMPERE 30” – 232W / 2.21A 36” – 232W / 2.21A 42” – 253W / 2.38A 48” – 258W / 2.41A NUMBER OF MOTORS 2 DESIGN 18-Gauge Seamless / Satin

Kobe Range Hoods CH7942SQB

heruntergeladen wurde: 3Dateigröße: 3 mb    Hersteller: Kobe Range Hoods  
Kategorie: Kraftstationen

- Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. - Temporarily wire the hood to test for proper operation before installing. - Peel protective film off the hood (if any). - For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not included) on each side. Refer to Figure 7. - Measure and create access opening for electrical wires under the cabinet or access opening for the electrical wires at

Kobe Range Hoods CH7936SQB

heruntergeladen wurde: 6Dateigröße: 3 mb    Hersteller: Kobe Range Hoods  
Kategorie: Kraftstationen

BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. Connect the electrical wires. -Connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to color: black to black, white to white, and green to green. -If necessary to hide the electrical wire connections, push wires back into the wiring box. Access the wire connections underneath the hood. Make sure wires do not

Kobe Range Hoods CH7948SQB

heruntergeladen wurde: 0Dateigröße: 3 mb    Hersteller: Kobe Range Hoods  
Kategorie: Kraftstationen

Mark the position of the duct cover-mounting bracket. Use reference E from Table 2 and measurements on Page 22-23. Attach and secure duct cover-mounting bracket with two screws (not provided). Refer to Figure 18. NOTE: Inner duct cover will cover the duct cover-mounting bracket. 4. Use aluminum or steel pipe to connect the plastic exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. 5. Connect electrical wires. Refer to “Wiring to Power Supply” on Pag

Kobe Range Hoods CH0336SQB

heruntergeladen wurde: 1Dateigröße: 3 mb    Hersteller: Kobe Range Hoods  
Kategorie: Kraftstationen

- Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and Fire Department right away. CAUTION 1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors. 2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) to prevent back drafting. 3) Follow the heating equipment manufacturer’s guideline and safety standards suc

Kobe Range Hoods CH0330SQB

heruntergeladen wurde: 0Dateigröße: 3 mb    Hersteller: Kobe Range Hoods  
Kategorie: Kraftstationen

Refer Figure 15. Slide the duct cover onto the hood. 6. Use 3/16” x 3/8” screws (included) to attach duct cover to hood. Figure 15 Install Accessories Figure 16 7. Attach oil tunnel. Refer to Figure 16. 8. Refer to Figure 17. Slide the baffle filter into the hood. Push the baffle filter upward. . Slide forward. Pull downward. Fit into place. 9. For bottom casing, repeat above steps. Refer to page 17. 10. Install heating lamps (not included), 120 Volts 175 Watts max. each. Final Assembly 11.





Kategorien