Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
# Since USB 2.0 Hi-Speed is an evolution of the existing USB 1.1 specification, it is fully forward and backward compatible with current USB systems. # If your computer’s USB controller is only USB1.1 you can only achieve a 4X maximum CD writing speed. # If you do not have a USB2.0 port, you may install an optional USB2.0 adapter or controller (see optional accessories section on page 13) to your computer to achieve the maximum DVD CD writing speed. USB interface cable installation Attach the USB 2.0 interface cable to the computer connector (C2, figure 1 on Page 6) at the back of the DVD DigiCopier firm and securely – you should not be able to disconnect the without pressing the release notch. USB driver installation For Win98 and Win98SE 1. Make sure your computer is up and running. 2. Insert the USB cable to the USB Port. 3. A "New Hardware Found" message shall pops up. 4. Follow the ON SCREEN wizard and point to the location of A:\USBWIN98 for the driver. 5. Let Windows finish the installation and that’s it. 6. Double click My Computer icon and there should be an extra drive letter for the DVD DigiCopier drive. 7. You may now access the drive. Note: USB DVD DigiCopier is Plug and Play under Windows XP, and Me, 2000. There is no third party driver needed. Note: When the DVD DigiCopier is used on a Computer, Only the DVD±R/RW drive at the bottom of the DVD DigiCopier will Work. The Regular DVDROM drive will be DISABLED Firewire interface cable installation Attach the Firewire interface cable to the computer connector (C2, figure 1 on Page 6) at the back of the DVD DigiCopier firm and securely – you should not be able to disconnect the cable without pressing the release notch. Firewire DVD DigiCopier Installation For Win98SE, Me, 2000 and XP Note for Win98SE only: After plugging in the cable some system might prompt you for Win98SE CD, in case you don’t have The Win98SE CD and the wizard prompt you for: NTMAP.SYS please type C:\WINDOWS\SYSTEM32\DRIVERS NTMAPHLP.PDR please type C:\WINDOWS\SYSTEM\IOSUBSYS IF the system did not prompt you for anything just follow the steps below 1. Make sure the Firewire cable is securely attach from the back of the drive. 2. Make sure that power is attached and turned 3. Power on the system. On the Window Desktop, double click on the MY COMPUTER icon. 4. Plug the Addonics Six Pin FIREWIRE-IDE cable into your computer’s FIREWIRE 5. Wait for a few seconds, your computer well. 6. Double Click on the “My Computer” DVD DigiCopier will appear You are now ready to RW drive in the DigiCopier. Serial ATA Cable Installation Attach the USB-IDE cable’s “ MC 36 Connector” to your Addonics Mobile Drive firm and securely – you should not be able to disconnect the cable without pressing the release notch. Serial ATA Combo Hard Drive Installation For Win98SE, Me, 2000 and XP Note: There no drivers needed to use the Serial ATA cable as long as the drivers are installed for the Serial ATA Controller card/chip. It is plug and play. 1. Make sure the Serial ATA cable is securely attach the drive. (For Addonics Pocket drives such Exdrive etc. you may attach the USB connector to the USB port of the computer to provide power for the pocket from system’s USB port power output. 2. Make sure that power is attach to 3. Power on the system or you may hot plug while system is on. 4. On the Window Desktop, double click on the MY COMPUTER icon. 5. Plug the Serial ATA connector your computer’s Serial port. 6. Wait for a few seconds, well. Double Click You are now Chapter 6 Software Installation CD Mastering Software installation: 1. Load the CD Mastering Disc onto the DVD±R/RW drive of the DVD DigiCopier (make sure you set the unit to operate as an External DVD±R/RW Burner – refer to Chapter 5, page 8). 2. Click on the Install Button to start installation process. 3. Follow the On screen Wizard for installation. 4. Wait for a few seconds to finish the installation. 5. Restart the system when prompted. 6. You may now burn CD or CD disc. Note: Serial Number or CD key can be found on the CD sleeve if prompted. Please read the on-line Help of the software for all the detail commands and features of the software. Power CD Software installation: 1. Place the MPEG II software CD in the DVD±R/RW drive of the DVD DigiCopier. (Make sure you set the unit to operate as an External DVD±R/RW Burner – refer to Chapter 5, page 8). 2. In “My Computer” double click the DVDROM icon. 3. Double click on the Power CD folder then the Setup.exe or just double click on “Set Up” icon and follow the on screen messages to load MPEG II software. 4. Serial Number or CD key can be found on the CD Sleeve if Prompted. (It starts with MV most of the time) # Click NO for the Diagnostics test. # DO not loose the CD Sleeve in case you need later on for reinstallation of the software. # Please read the on-line Help of the software Detail commands and features Chapter 7 Playing Audio CDs You can use the Addonics DVD DigiCopier drive to play regul...